Why does my KTM 1290 Super Duke GT start in gear?
If the engine turns on your KTM Motorcycle even when a gear is engaged, the safety start system may be faulty. To address this, read out the fault memory using the KTM diagnostics tool.
What to do if the ABS warning lamp lights up on my KTM Motorcycle?
If the ABS warning lamp lights up on your KTM Motorcycle, it may be due to a blown ABS fuse. In this case, replace the fuses in the fuse box. It could also indicate a large difference in wheel speeds; try stopping the motorcycle, switching off the ignition, and starting it again.
Why does the combination instrument show nothing in the display of my KTM Motorcycle?
If the combination instrument on your KTM Motorcycle shows nothing on the display, it could be due to a blown fuse. Replace the fuses in the fuse box. Alternatively, the main fuse might be blown, in which case you should replace the main fuse. Another possible cause is a discharged 12-V battery; in this case, charge the 12-V battery and check the open-circuit current.
General| Displacement | 1301 cc |
|---|---|
| Torque | 141 Nm |
| Transmission | 6-speed |
| Seat Height | 835 mm |
| Dry Weight | 209 kg |
| Front Suspension | WP semi-active suspension USD Ø 48 mm |
| Rear Suspension | WP semi-active suspension monoshock |
| ABS | Bosch 9ME Combined-ABS (disengageable) |
| Engine Type | V-Twin, 4-stroke |
| Power | 173 hp (127 kW) @ 9500 rpm |
| Fuel Capacity | 23 liters |
| Front Brake | Dual 320 mm discs, Brembo 4-piston calipers |
| Rear Brake | 240 mm disc, 2-piston fixed caliper |
| Traction Control | MTC (Motorcycle Traction Control) |
| Wheelbase | 1482 mm |
| Frame | Chromoly steel trellis frame |
Emphasizes the importance of following safety instructions for safe operation.
Provides critical safety guidelines for operating the vehicle responsibly.
Stresses the importance of reading and keeping the manual accessible for reference.
Details the location of the VIN, stamped on the steering head and on the type label.
Explains where to find the key number on the KEYCODECARD for spare keys.
Specifies the location of the engine number, stamped on the right side of the engine.
Describes the clutch lever on the left handlebar and its automatic adjustment.
Locates the hand brake lever on the right handlebar for engaging the front brake.
Identifies the throttle grip on the right side of the handlebar.
Details the function of the combination switch located on the left side of the handlebar.
Describes the buttons for navigating the instrument cluster's matrix display.
Explains the operation of the cruise control system activation and speed setting.
Details the functions of the combination switch located on the right side of the handlebar.
Describes the functions of the emergency OFF and starter button in different positions.
Details the Race-on tip switch function for ignition lock and steering lock.
Explains the functions of the Race-on key, including ignition and case unlocking.
Describes the electronic steering lock system operated by the remote key.
Provides instructions and safety warnings for opening the fuel tank filler cap.
Locates the shift lever and illustrates the gear positions.
Overview of the instrument cluster, divided into indicator lamps and display areas.
Provides a detailed layout of the information displayed on the instrument cluster.
Shows the operating state and active status of the cruise control system.
Shows the ABS mode setting and how to configure ABS in the Motorcycle menu.
Indicates whether the Motorcycle Traction Control (MTC) system is switched on or off.
Shows navigation information such as direction, distance, and arrival time.
Explains how to navigate the instrument cluster menu using the control buttons.
Details the KTM MY RIDE function for smartphone connectivity and navigation.
Describes how to use the navigation function and configure settings.
Lists all active warnings and how they are stored and displayed in the Warnings menu.
Shows the next service interval and how to access service information.
The main menu for configuring ABS, chassis, traction control, and extra functions.
Explains the operation and control of Motorcycle Traction Control (MTC).
Details the combined MTC and Engine Braking Control (MSR) functions.
Explains the selection and operation of different ABS modes (Road, Supermoto).
Allows configuration of display units, values, and function enablement/disablement.
Details the activation and deactivation of the Quickshift + function.
Describes the optional TRACK drive mode for enhanced performance.
Describes the Anti Wheelie Mode and safety warnings for its deactivation.
Provides essential safety and operational advice before the initial ride.
Details the recommended engine speed limits during the initial running-in phase.
Explains the impact of weight and axle loads on handling characteristics.
Lists essential pre-ride checks to ensure the vehicle is roadworthy.
Provides a step-by-step guide for starting the motorcycle's engine.
Explains the optional Launch Control feature for optimal acceleration from a standstill.
Details how to use Launch Control for starting off, including conditions and warnings.
Describes the Anti Wheelie Mode feature intended to prevent front wheel lift.
Explains the Quickshifter + function for clutchless up and down gear shifts.
Provides guidance on gear shifting, load alterations, and passenger safety.
Provides crucial information and warnings regarding brake system operation and maintenance.
Provides essential information and safety precautions for refueling the motorcycle.
Lists compulsory maintenance tasks with their recommended service intervals.
Describes the semi-active suspension system and its tuning capabilities.
Explains the ABS unit, sensors, operating modes, and safety warnings.
Provides step-by-step instructions for removing the front wheel.
Details the procedure for installing the front wheel, including bearing checks.
Provides step-by-step instructions for removing the rear wheel.
Details the procedure for installing the rear wheel, including bearing checks.
Guides on inspecting tires for cuts, damage, and tread depth.
Explains how to check tire pressure when tires are cold and correct if necessary.
Locates the 12V socket for electrical accessories and its specifications.
Provides instructions and safety warnings for checking the coolant level.
Allows selection of engine and traction control settings for different riding conditions.
Explains the operation and control of Motorcycle Traction Control (MTC).
Allows tuning the MTC system through levels for desired characteristic map.
Explains how to adjust the throttle response characteristic map.
Provides instructions for checking the engine oil level in the viewer.
Details the procedure for changing engine oil, filter, and cleaning oil screens.
Provides instructions for adding engine oil and checking the level.
Lists critical engine component tightening torques for proper assembly.
Provides detailed specifications for the front fork, including spring rates and oil volume.
Provides detailed specifications for the rear shock absorber, including spring rates.
Lists critical chassis component tightening torques for proper assembly.
Provides standard classification and recommended supplier for SAE 10W/50 engine oil.
Provides standard classification and recommended supplier for SAE 5W/40 engine oil.
Specifies the standard for unleaded super fuel and its grade equivalency.
To Next Page