KTM 1290 Super Duke GT 2018

Other manuals for KTM 1290 Super Duke GT 2018

Setup Instructions22 pages

Questions and Answers

P
Paul FreemanAug 13, 2025
What to do if my KTM 1290 Super Duke GT 2018 Motorcycle engine does not crank when pressing the electric starter button?
- R
  Rachel StewartAug 13, 2025
  If your KTM motorcycle engine isn't cranking when you press the electric starter, consider these potential causes and solutions: * The emergency OFF switch is off: Press the emergency OFF switch to the ON position. * Operating error: Follow the correct start procedure. * The battery is discharged: Recharge the battery and check the open-circuit current. * The safety start system is faulty: Read out the fault memory using the KTM diagnostics tool. * CAN bus communication error: Read out the fault memory using the KTM diagnostics tool. * Fault in the engine electronics control unit: Read out the fault memory using the KTM diagnostics tool. * Fault in the MCU control unit: Read out the fault memory using the KTM diagnostics tool.
J
Jeff RodriguezAug 17, 2025
What to do if my KTM Motorcycle engine turns but does not start?
- W
  washingtonchristinaAug 17, 2025
  If the engine turns over but doesn't start, check these: * The fuel hose connection: Reconnect the coupling of the fuel hose connection if it is not connected. * Fuel injection system: Read out the fault memory using the KTM diagnostics tool, as there may be a defect. * Fuel quality: Add suitable fuel if the current fuel is insufficient.
S
Shannon DanielAug 20, 2025
What causes high oil consumption in my KTM 1290 Super Duke GT 2018 Motorcycle?
- T
  Timothy MontgomeryAug 20, 2025
  High oil consumption in your KTM motorcycle could be due to: * Engine oil level being too high: Check the engine oil level. * Engine oil being too thin (low viscosity): Change the engine oil and oil filter, and clean the oil screens.
M
Mike DominguezAug 25, 2025
What to do if my KTM 1290 Super Duke GT 2018 engine dies during the trip?
- R
  rhonda99Aug 26, 2025
  If your KTM motorcycle engine dies while you're riding, it could be due to: * Lack of fuel: Refuel the motorcycle. * Defect in the fuel injection system: Read out the fault memory using the KTM diagnostics tool.
A
Andrea WatsonAug 28, 2025
Why is my KTM 1290 Super Duke GT 2018 battery discharged?
- M
  Michael RothAug 28, 2025
  A discharged battery in your KTM motorcycle may be caused by: * The hazard warning flasher being switched on: Switch off the hazard warning flasher and recharge the battery. * The battery not being charged by the alternator: Check the charging voltage. * The ignition not being switched off while parked: Recharge the battery.
B
Bradley HammondSep 1, 2025
What to do if the combination instrument shows nothing on the display of my KTM Motorcycle?
- B
  Brandon TurnerSep 1, 2025
  If the combination instrument display is blank, there could be several reasons: * Fuse 1 might be blown: Change the fuses in the fuse box. * The main fuse might be blown: Change the main fuse. * The battery might be discharged: Recharge the battery and check the open-circuit current. * The ignition/steering lock might be faulty: Check the ignition/steering lock.
J
Jonathan CruzSep 4, 2025
Why does the ABS indicator lamp light up on my KTM Motorcycle?
- K
  Kendra PatelSep 5, 2025
  The ABS indicator lamp might light up on your KTM motorcycle due to: * A blown ABS fuse: Replace the fuses in the fuse box. * A large difference in wheel speeds: Stop the vehicle, switch off the ignition, and start it again. * A malfunction in the ABS: Read out the fault memory using the KTM diagnostics tool.
S
Sharon OliverSep 9, 2025
What does it mean if the malfunction indicator lamp lights up or flashes on my KTM 1290 Super Duke GT 2018 Motorcycle?
- R
  Rhonda Miller DDSSep 9, 2025
  If the malfunction indicator lamp lights up or flashes, it indicates a defect in the fuel injection system. You should read out the fault memory using the KTM diagnostics tool.

Summary

Safety Advice

Use Definition - Intended Use

Specifies the vehicle's intended use for regular traffic and race courses, not offroad.

Misuse

Warns about dangers arising from using the vehicle not as intended, including improper fluids.

Safety Advice

Emphasizes following safety instructions for safe operation, highlighted in the text.

Degrees of Risk and Symbols

Explains symbols for Danger, Warning, Caution, Note, and their associated risk levels.

Tampering Warning

Prohibits tampering with the noise control system and lists acts presumed to constitute tampering.

Safe Operation

Provides safety instructions regarding rider fitness, alcohol, drugs, and physical impairment.

Protective Clothing

Stresses the importance of wearing appropriate protective clothing for all rides for safety.

Serial Numbers

Chassis Number

Details the location of the chassis number stamped on the right side of the steering head.

Type Label

Describes the location of the type label, which is situated on the steering head.

Engine Number

Details the location of the engine number stamped on the right side of the engine.

Controls

Clutch Lever

Describes the clutch lever on the left handlebar, its hydraulic activation, and automatic adjustment.

Hand Brake Lever

Details the hand brake lever on the right handlebar used for engaging the front brake.

Throttle Grip

Locates the throttle grip on the right side of the handlebar.

Switches on the Left Side of the Handlebar

Details the switches located on the left side of the handlebar, including the combination switch.

Light Switch

Explains the operation of the light switch with its possible states: low beam, high beam, and flasher.

Hazard Warning Flasher Switch

Turn Signal Switch

Switches on the Right Side of the Handlebar

Emergency OFF Switch

Explains the function of the emergency OFF switch in ON and OFF positions.

Switch for the Cruise Control System

Describes the cruise control system switch and its states for activating/deactivating the function.

Upper Button of the Cruise Control System

Details the function of the upper cruise control button for setting and increasing target speed.

Lower Button of the Cruise Control System

Explains the function of the lower cruise control button for activating and decreasing target speed.

Electric Starter Button

Locking the Steering

Unlocking the Steering

Ignition;Steering Lock

Immobilizer

Opening the Filler Cap

Provides warnings about fire hazard related to fuel and instructions for opening the filler cap.

Closing the Filler Cap

Details the procedure for closing the filler cap, including warnings about damage and fire hazard.

Shift Lever

Foot Brake Lever

Combination Instrument

Overview

Matrix Display

Segment Display

Indicator Lamps

Lists and describes various indicator lamps for high beam, immobilizer, oil pressure, and turn signals.

Message on the Matrix Display

Matrix Display Menu

Ergonomics

Handlebar Position

Adjusting the Handlebar Position

Provides detailed steps for adjusting handlebar position, including torque specifications.

Adjusting the Steering Angle

Adjusting the Basic Position of the Clutch Lever

Guides on adjusting the clutch lever's basic position using an adjusting screw for hand size.

Adjusting the Basic Position of the Hand Brake Lever

Guides on adjusting the hand brake lever's basic position using an adjusting screw for hand size.

Adjusting the Basic Position of the Foot Brake Lever

Details adjusting the foot brake lever's basic position by turning a push rod and locking a nut.

Setting the Step Plate of the Foot Brake Lever

Adjusting the Basic Position of the Shift Lever

Details how to adjust shift lever position by loosening nuts and turning a threaded rod.

Setting the Shift Lever Stub

Preparing for Use

Advice on Preparing for First Use

Offers advice on rider fitness, protective clothing, tire patterns, and approved tires/wheels.

Running in the Engine

Loading the Vehicle

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Lists essential checks before every trip, including fluid levels, brakes, tires, and controls.

Starting the Vehicle

Details the procedure for starting the engine, including safety warnings and notes on engine damage.

Starting Off

Explains how to start riding by coordinating clutch lever release and throttle application.

Quickshifter

Shifting, Riding

Provides warnings about abrupt load changes, downshifting at high RPM, and ignition key position.

Applying the Brakes

Provides warnings on brake system impairment due to moisture, dirt, overheating, and salt.

Refueling

Details refueling procedure, including warnings about fire hazard and fuel quality.

Service Schedule

Required Work

Suspension Setting

Fork;Shock Absorber

Load

Damping

Service Work on the Chassis

Cleaning the Chain

Checking the Chain Tension

Adjusting the Chain Tension

Explains how to adjust chain tension by turning the hub housing and tightening the eccentric screw.

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Checking;Correcting the Fluid Level of the Hydraulic Clutch

Provides warnings on skin irritation and environmental hazards of brake fluid, and how to check/correct the level.

Brake System

Antilock Brake System (ABS)

Describes the ABS unit, sensors, and warnings regarding vehicle changes affecting ABS function.

Checking the Brake Discs

Details how to check brake disc thickness, wear limits, and for damage, cracking, or deformation.

Checking the Front Brake Fluid Level

Warns about insufficient brake fluid causing system failure and old fluid reducing braking effect.

Adding Front Brake Fluid

Provides warnings on brake fluid hazards and instructions for adding front brake fluid.

Checking the Front Brake Linings

Warns about worn brake linings reducing braking effect and details how to check minimum thickness.

Checking the Rear Brake Fluid Level

Warns about insufficient brake fluid causing system failure and old fluid reducing braking effect.

Adding Rear Brake Fluid

Provides warnings on brake fluid hazards and instructions for adding rear brake fluid.

Checking the Brake Linings of the Rear Brake

Warns about worn brake linings reducing braking effect and details how to check minimum thickness.

Wheels, Tires

Removing the Front Wheel

Installing the Front Wheel

Removing the Rear Wheel

Installing the Rear Wheel

Checking the Tire Condition

Warns about tire bursts, handling impairment from different tread patterns, and non-approved tires.

Checking the Tire Air Pressure

Explains the importance of correct tire air pressure for wear, overheating, comfort, and service life.

Electrical System

Removing the Battery

Installing the Battery

Changing the Main Fuse

Warns about incorrect fuses overloading the electrical system and how to change the main fuse.

Changing the Fuses in the Fuse Box

Explains how to change fuses, lists fuse functions, and provides fuse rating guidelines.

Activating;Deactivating the Ignition Key

Cooling System

Checking the Coolant Level in the Compensating Tank

Provides warnings on scalding and poisoning hazards of coolant and how to check the level.

Correcting the Coolant Level in the Compensating Tank

Provides warnings on coolant hazards and instructions for correcting the coolant level in the compensating tank.

Engine Tuning

Drive Mod

Motorcycle Traction Control (MTC)

Service Work on the Engine

Checking the Engine Oil Level

Explains how to check engine oil level in the viewer and when to add engine oil.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screens

Provides warnings on scalding and environmental hazards of engine oil, and outlines the process.

Adding Engine Oil

Warns about low/poor engine oil causing wear and damage, and how to add engine oil.

Storage

Troubleshooting

Technical Data

Engine

Engine Tightening Torques

Lists engine tightening torques for various screws and bolts with applicable Loctite specifications.

Chassis

Chassis Tightening Torques

Substances