What if valve clearance too little on KTM 250 XCF-W USA 2010 Motorcycle?
If your KTM Motorcycle engine has too little power, it may be because the valve clearance is too little. Adjust the valve clearance.
What to do if electrode distance of spark plug too wide on KTM 250 XCF-W USA 2010?
If your KTM Motorcycle engine turns but does not start, and the electrode distance (plug gap) of the spark plug is too wide, adjust the plug gap. The guideline spark plug electrode gap is 0.7 mm (0.028 in).
What to do if lack of fuel on KTM 250 XCF-W USA 2010 Motorcycle?
If your KTM Motorcycle engine stalls or is popping into the carburetor, it could be due to a lack of fuel. Turn the handle of the fuel tap to the ON position or fill up with fuel.
What if there is too little air stream on KTM Motorcycle?
If the KTM Motorcycle engine overheats, it might be due to too little air stream. Switch off the engine when standing.
What to do if foam formation in cooling system on KTM 250 XCF-W USA 2010?
If the KTM Motorcycle engine overheats, it could be due to foam formation in the cooling system. Drain and refill the coolant.
What to do if speedometer values deleted on KTM Motorcycle?
If the speedometer values are deleted (time, stop watch, lap times) on KTM Motorcycle, the battery in the speedometer is empty. Change the battery in the speedometer.
General| Engine Type | Single-cylinder, 4-stroke |
|---|---|
| Compression Ratio | 12.8:1 |
| Transmission | 6-speed |
| Starter | Electric starter |
| Bore x Stroke | 76 mm x 55 mm |
| Fuel System | Electronic Fuel Injection |
| Front Suspension | WP USD 48 mm |
| Rear Suspension | WP PDS shock |
| Front Brake | Disc brake |
| Rear Brake | Disc brake |
| Frame | Chromoly steel |
Explains symbols used throughout the manual for clarity.
Explains typographical and other formats used in the manual.
Defines the intended use and limitations for the 250 EXC-F EU model.
Defines the intended use and limitations for the 250 XCF-W USA model.
Provides safety notes for transport and encourages environmental responsibility.
Explains risk symbols and stresses manual importance.
Illustrates and labels the left front view of the motorcycle.
Illustrates and labels the right rear view of the motorcycle.
Shows locations for chassis, type, and key numbers.
Shows locations for engine and fork part numbers.
Shows the location of the shock absorber part number.
Covers clutch, hand brake, short circuit, and starter buttons.
Details light switch, horn, turn signals, and indicator lamps.
Explains speedometer operation, modes, and unit settings.
Guides on setting the clock and adjusting speedometer display modes.
Explains querying lap times and speed display mode.
Explains the SPEED/H display for service hours.
Explains SPEED/CLK, SPEED/LAP, and SPEED/ODO display modes.
Explains the SPEED/TR1 display mode.
Explains SPEED/TR2, SPEED/A1, and SPEED/A2 display modes.
Explains SPEED/S1 and SPEED/S2 stop watch modes.
Covers fuel tap states and filler cap procedures.
Explains choke lever function for cold starts.
Covers choke for USA model and shift lever operation.
Explains foot brake pedal and kickstarter usage.
Explains side stand safety and steering lock functions.
Guides on how to unlock the steering.
Crucial safety advice and preparation for the first ride.
Advises on weight limits and engine break-in procedures.
Lists essential checks and engine starting steps.
Guides on starting, shifting, and braking techniques.
Covers procedures and safety for stopping, parking, and refueling.
Lists maintenance tasks for authorized KTM workshops.
Lists routine checks and maintenance for the rider.
Covers basic chassis setting and shock absorber damping.
Details adjusting compression and rebound damping.
Guides on checking and adjusting shock absorber sag.
Covers fork damping and setting checks.
Guides on adjusting fork spring preload and bleeding fork legs.
Guides on cleaning fork protector dust boots.
Covers loosening, positioning fork protection and checking steering head bearing.
Guides on adjusting steering head bearing play.
Explains fork offset and guides on removing fork legs.
Guides on installing fork legs.
Guides on removing the lower triple clamp.
Guides on installing the lower triple clamp.
Guides on removing and installing the fork protector.
Guides on removing the lower triple clamp for both models.
Guides on installing the lower triple clamp for the EU model.
Guides on installing the lower triple clamp for the USA model.
Guides on greasing the steering head bearing.
Guides on removing and installing the front fender.
Guides on removing and refitting the headlight mask.
Guides on removing and installing the start number plate.
Explains handlebar positions and guides on adjusting them.
Explains how to check the correct routing of the throttle cable.
Guides on checking and adjusting throttle cable play.
Guides on checking the chain for dirt accumulation.
Instructions on cleaning the chain and checking its tension.
Guides on checking sprockets and chain wear.
Guides on adjusting the chain tension.
Details chain tension adjustment procedures.
Guides on adjusting the chain guide and clutch lever position.
Guides on checking and changing hydraulic clutch fluid.
Guides on checking brake discs and hand brake lever free travel.
Guides on adjusting hand brake lever free travel and position.
Guides on checking the front brake fluid level.
Detailed steps for adding front brake fluid.
Guides on checking and replacing front brake linings.
Detailed steps for changing front brake linings.
Guides on checking foot brake lever travel and adjusting position.
Guides on checking the rear brake fluid level.
Detailed steps for adding rear brake fluid.
Guides on checking and replacing rear brake linings.
Detailed steps for changing rear brake linings.
Guides on removing and installing the front wheel.
Guides on installing the front wheel.
Guides on removing and installing the rear wheel.
Guides on checking tire condition, tread depth, and age.
Provides correct tire pressures and guides on spoke tension checks.
Guides on battery removal, installation, and recharging.
Guides on locating, removing, and replacing fuses.
Covers seat removal and fuel tank removal.
Guides on safely installing the fuel tank.
Covers cooling system checks and coolant refilling.
Guides on checking coolant level and draining the coolant.
Guides on refilling coolant and silencer removal/installation.
Guides on air filter box and air filter removal/installation.
Guides on air filter cleaning and carburetor idle importance.
Guides on adjusting idle and emptying float chamber.
Guides on checking the engine oil level.
Guides on draining engine oil and cleaning oil screens.
Guides on removing the oil filter.
Guides on installing oil filter and filling engine oil.
Troubleshooting for cranking and starting problems.
Troubleshooting for idle and speed-up issues.
Troubleshooting for low power and overheating.
Troubleshooting for oil consumption and battery discharge.
Provides guidelines and warnings for cleaning the motorcycle.
Procedures for storing the motorcycle for extended periods.
Guides on preparing the motorcycle after storage.
Details engine design, displacement, bore, and valve clearances.
Specifies engine oil and coolant capacities.
Lists tire specifications and fuel tank capacity.
Details specifications for the motorcycle's lighting system.
Details fork damping and spring preload settings.
Details shock absorber damping and spring preload settings.
Electrical wiring diagram for the 250 EXC-F EU model.
List of electrical components and color codes used in diagrams.
Specifications for brake fluid and coolant.
Specifications for various oils and fuel type.
Lists recommended lubricants and cleaning agents.
Lists recommended cleaners, polishes, greases, and sprays.
Recommended air filter oil and universal spray.
Explains the standard for motorcycle engine oils.
Explains SAE viscosity classifications for oils.
To Next Page
