KTM 350 XC-F User Manual (English)

Other manuals for KTM 350 XC-F

Questions and Answers:

Z
zgarnerSep 4, 2025
What to do if my KTM 350 XC-F engine turns but does not start?
- E
  Eric GriffinSep 4, 2025
  If your KTM Motorcycle engine turns but doesn't start, consider these potential causes: * Ensure the fuel hose connection is properly connected. * If the fuel screen in the fuel hose connection is clogged, replace it. * Adjust the idle speed if it's not correctly set. * Clean and dry the spark plug if it's oily or wet, or replace it if necessary. * Adjust the spark plug gap to the recommended 0.8 mm (0.031 in) if it's too wide. * Check the wiring harness for frayed short circuit cables and inspect the kill switch for defects. Also, check the electrical system. * If there's a defect in the fuel injection system, use the KTM diagnostics tool to read the fault memory.
K
Kathleen CastroSep 6, 2025
What to do if the KTM Motorcycle engine does not turn when the starter button is pressed?
- M
  Mr. Patrick Thompson DVMSep 6, 2025
  If your KTM Motorcycle engine doesn't turn when you press the starter, it could be due to several reasons. You might not be following the correct start procedure. The battery could be discharged, requiring a recharge, voltage check, quiescent current check, and stator winding inspection. The main fuse might be blown, necessitating a replacement. Alternatively, the starter relay or the starter motor itself could be defective, requiring a check.
R
Ricardo BeckerSep 7, 2025
What does it mean if the FI warning lamp (MIL) lights up/flashes on my KTM Motorcycle?
- C
  corey83Sep 7, 2025
  If the FI warning lamp (MIL) lights up or flashes on your KTM Motorcycle, it could indicate a defect in the fuel injection system. Stop the motorcycle and identify the faulty part using the blink code. Also, check the cabling for damage and the electrical plug-in connections for corrosion and damage. The fault memory can be read out using the KTM diagnostics tool. Other potential causes include a bent engine vent hose (straighten or replace it), an engine oil level that is too high (check and adjust), or engine oil that is too thin (low viscosity), requiring an engine oil and oil filter change, and cleaning of the oil screen.
B
Benjamin EdwardsSep 8, 2025
Why is my KTM 350 XC-F Motorcycle engine overheating?
- L
  lperezSep 8, 2025
  If your KTM Motorcycle engine overheats, several factors could be the cause. There might be too little coolant in the cooling system, so check the system for leakage and verify the coolant level. Insufficient air stream could be a factor; switch off the engine when standing. Very dirty radiator fins can also cause overheating, so clean them. Foam formation in the cooling system requires draining and refilling the coolant. Lastly, a bent radiator hose should be replaced.
R
Robert RichardsonSep 10, 2025
What to do if the KTM 350 XC-F Motorcycle engine does not turn when the start button is pressed?
- C
  clarkbrianSep 10, 2025
  If your KTM Motorcycle's engine doesn't turn over when you press the start button, here's what might be happening: * **Operating Error**: Make sure you're following the correct start procedure. * **Flat Battery**: The 12-V battery could be discharged. In this case, charge the 12-V battery and check the charging voltage, open-circuit current and the stator winding of the alternator. * **Blown Fuse**: The main fuse might have blown, so replace the main fuse. * **Starter Relay/Motor**: There could be a faulty starter relay or starter motor. Check the starter relay and the starter motor.

KTM 350 XC-F Specifications

General

Displacement	349.7 cc
Bore/Stroke	88 mm / 57.5 mm
Starter	Electric starter
Transmission	6-speed
Cooling	Liquid cooled
Front Suspension	WP XACT-USD, Ø 48 mm
Rear Suspension	WP XACT Monoshock with linkage
Ground Clearance	370 mm
Engine Type	Single-cylinder, 4-stroke
Fuel System	Keihin EFI, 44 mm Throttle Body
Frame	Central double-cradle type, 25CrMo4 steel
Front Brake	Disc brake, 260 mm
Rear Brake	Disc brake, 220 mm
Fuel Tank Capacity	8.5 liters

Summary

Means of Representation

Symbols Used

Explains the meaning of various symbols used in the manual.

Formats Used

Explains the typographical formats used throughout the document.

Safety Advice

Use Definition – Intended Use

Defines the intended purpose and usage of the vehicle.

Misuse

Describes improper uses of the vehicle and potential dangers.

Safety Advice

Provides general safety instructions and warnings.

Degrees of Risk and Symbols

Explains hazard symbols and their associated risk levels.

Tampering Warning

Warns against unauthorized modifications to the noise control system.

Safe Operation

Provides guidelines for safe operation, including dangers of accidents and poisoning.

Protective Clothing

Emphasizes the importance of wearing appropriate protective clothing.

Work Rules

Outlines general rules to follow when performing work on the vehicle.

Environment

Advises on responsible use and disposal of materials for environmental protection.

Owner's Manual

Stresses the importance of reading and understanding the manual.

Important Notes

Manufacturer Warranty, Implied Warranty

Explains warranty conditions and exclusions for service work.

Fuel, Auxiliary Substances

Details requirements for fuel and auxiliary substances.

Spare Parts, Technical Accessories

Recommends using approved parts and accessories for safety.

Service

Highlights the importance of proper service for vehicle longevity and performance.

Figures

Notes that figures may depict special equipment and may not show full disassembly.

Customer Service

Directs users to authorized dealers for questions and support.

View of Vehicle

View of Vehicle, Front Left (Example)

Illustrates and labels components on the front left side of the vehicle.

View of Vehicle, Rear Right (Example)

Illustrates and labels components on the rear right side of the vehicle.

Serial Numbers

Vehicle Identification Number

Shows where to find the vehicle identification number (VIN).

Steering Head Label

Indicates the location of the steering head label.

Engine Number

Shows where to find the engine number.

Fork Article Number

Shows where to find the article number for the fork.

Shock Absorber Article Number

Shows where to find the article number for the shock absorber.

Controls

Clutch Lever

Describes the clutch lever location and operation.

Hand Brake Lever

Describes the hand brake lever location and function.

Throttle Grip

Describes the throttle grip location and function.

Stop Button

Explains the location and states of the stop button.

Start Button

Describes the start button location and its possible states.

Combination Switch

Details the combination switch functions and mapping options.

Overview of Indicator Lights

Explains the meaning of various indicator lamps on the vehicle.

Combination Instrument

Describes the combination instrument and its display functions.

Opening the Fuel Tank Filler Cap

Provides instructions and safety warnings for opening the fuel tank cap.

Closing the Fuel Tank Filler Cap

Provides instructions for closing the fuel tank filler cap.

Cold Start Button

Explains the function and operation of the cold start button.

Idle Speed Adjusting Screw

Details how to adjust the idle speed using the adjusting screw.

Shift Lever

Shows gear positions and neutral for SX-F and XC-F models.

Foot Brake Lever

Describes the location and use of the foot brake lever.

Plug-in Stand (All SX-F Models)

Explains the use of the plug-in stand for parking and transport.

Side Stand (XC-F US)

Describes the use and securing of the side stand.

Preparing for Use

Advice on Preparing for First Use

Covers safety advice, clothing, and initial checks before riding.

Running in the Engine

Provides guidelines for the engine break-in period.

Starting Power of Lithium-ion Batteries at Low Temperatures

Explains starting procedures for lithium-ion batteries in cold conditions.

Preparing for Difficult Operating Conditions

Advises on pre-ride checks for various challenging conditions.

Preparing for Rides on Dry Sand

Details preparations for riding on dry sand, including air filter covers.

Preparing for Rides on Wet Sand

Outlines preparations for riding on wet sand.

Preparing for Rides on Wet and Muddy Circuits

Details preparations for riding on wet and muddy circuits.

Preparing for High Temperatures or Slow Riding

Advises on preparations for hot conditions or slow riding.

Preparing for Low Temperatures or Snow

Details preparations for riding in cold conditions or snow.

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Lists pre-ride checks for safety and operation.

Starting the Vehicle

Provides instructions and safety warnings for starting the engine.

Activating Launch Control

Explains how to activate launch control for optimal acceleration.

Activating Traction Control

Describes how to activate and use traction control.

Starting Off

Provides instructions for moving off from a standstill.

Quickshifter (All SX-F Models)

Explains the function and activation of the quickshifter.

Activating the Quickshifter (All SX-F Models)

Details the procedure for activating the quickshifter.

Shifting, Riding

Guides on gear shifting and general riding techniques.

Applying the Brakes

Provides instructions and warnings on brake application.

Stopping, Parking

Explains procedures for stopping and parking the motorcycle safely.

Transporting

Provides guidance on transporting the motorcycle securely.

Refueling

Details safety precautions and procedures for refueling.

Refueling

Continues refueling instructions, including fuel types and tank capacity.

Service Schedule

Additional Information

Explains how service intervals may vary by country and conditions.

Service Schedule

Presents a schedule of maintenance tasks and their intervals.

Tuning the Chassis

Checking the Basic Chassis Setting with Rider's Weight

Explains how to adjust chassis settings based on rider weight.

Air Suspension XACT

Describes the WP XACT air suspension system used in the fork.

Compression Damping of the Shock Absorber

Explains high-speed and low-speed compression damping.

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Provides steps to adjust low-speed compression damping on the shock absorber.

Adjusting the High-Speed Compression Damping of the Shock Absorber

Guides on adjusting high-speed compression damping on the shock absorber.

Adjusting the Rebound Damping of the Shock Absorber

Provides instructions for adjusting rebound damping on the shock absorber.

Measuring the Dimension of the Rear Wheel Unloaded

Details how to measure rear wheel dimension without load.

Checking the Static Sag of the Shock Absorber

Explains how to check static sag of the shock absorber.

Checking the Riding Sag of the Shock Absorber

Explains how to check riding sag of the shock absorber.

Adjusting the Spring Preload of the Shock Absorber

Guides on adjusting the spring preload for optimal suspension.

Adjusting the Spring Preload of the Shock Absorber

Provides steps to adjust spring preload on the shock absorber.

Adjusting the Riding Sag

Details how to adjust the riding sag for the shock absorber.

Checking the Basic Setting of the Fork

Explains how to check the basic settings of the front fork.

Adjusting the Fork Air Pressure

Guides on adjusting air pressure in the front fork suspension.

Adjusting the Compression Damping of the Fork

Explains how to adjust compression damping on the front fork.

Adjusting the Rebound Damping of the Fork

Guides on adjusting rebound damping on the front fork.

Handlebar Position

Explains handlebar mounting positions and adjustments.

Adjusting the Handlebar Position

Provides steps for adjusting the handlebar position.

Service Work on the Chassis

Raising the Motorcycle with a Lift Stand

Details procedures for safely lifting the motorcycle on a stand.

Removing the Motorcycle from the Lift Stand

Explains how to safely remove the motorcycle from a lift stand.

Bleeding the Fork Legs

Provides instructions for bleeding air from the fork legs.

Cleaning the Dust Boots of the Fork Legs

Details how to clean dust boots on the fork legs.

Removing the Fork Protector

Guides on removing the fork protector.

Installing the Fork Protector

Details how to install the fork protector.

Removing the Fork Legs

Provides instructions for removing the front fork legs.

Installing the Fork Legs

Details how to install the front fork legs correctly.

Removing the Lower Triple Clamp

Guides on removing the lower triple clamp assembly.

Installing the Lower Triple Clamp

Details the installation of the lower triple clamp assembly.

Checking the Steering Head Bearing Play

Explains how to check for play in the steering head bearings.

Adjusting the Steering Head Bearing Play

Guides on adjusting the steering head bearing play.

Lubricating the Steering Head Bearing

Describes the process of lubricating the steering head bearing.

Removing the Start Number Plate

Guides on removing the front start number plate.

Installing the Start Number Plate

Details how to install the front start number plate.

Removing Front Fender

Provides instructions for removing the front fender.

Installing Front Fender

Details how to install the front fender.

Removing the Shock Absorber

Guides on removing the rear shock absorber.

Installing the Shock Absorber

Details how to install the rear shock absorber.

Installing the Shock Absorber

Continues installation steps for the rear shock absorber.

Removing the Seat

Guides on removing the motorcycle seat.

Mounting the Seat

Details how to install the motorcycle seat.

Removing the Air Filter Box Cover

Guides on removing the air filter box cover.

Installing the Air Filter Box Cover

Details how to install the air filter box cover.

Removing the Air Filter

Guides on removing the air filter.

Cleaning the Air Filter and Air Filter Box

Details how to clean the air filter and its box.

Installing the Air Filter

Details how to install the air filter correctly.

Preparing Air Filter Box Cover for Securing

Guides on preparing the air filter box cover for securing.

Removing the Main Silencer

Provides instructions for removing the main silencer.

Installing the Main Silencer

Details how to install the main silencer.

Changing the Glass Fiber Yarn Filling of the Main Silencer

Guides on replacing the glass fiber yarn filling in the silencer.

Removing the Fuel Tank

Provides instructions for removing the fuel tank.

Installing the Fuel Tank

Details how to install the fuel tank.

Checking for Chain Dirt Accumulation

Explains how to check the chain for dirt buildup.

Cleaning the Chain

Provides instructions and warnings for cleaning the motorcycle chain.

Checking the Chain Tension

Guides on how to check and set the correct chain tension.

Adjusting the Chain Tension

Details the procedure for adjusting the chain tension.

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Guides on checking wear of chain, sprockets, and chain guide.

Checking the Frame

Explains how to check the frame for damage or deformation.

Checking the Link Fork

Guides on checking the link fork for damage or cracking.

Checking the Throttle Cable Routing

Details how to check the routing of throttle cables.

Checking the Rubber Grips

Guides on checking handlebar rubber grips for wear and damage.

Programming the Quickshifter (All SX-F Models)

Explains how to reprogram the quickshifter if performance decreases.

Adjusting the Basic Position of the Clutch Lever

Guides on adjusting the clutch lever position for hand size.

Checking/Correcting the Fluid Level of the Hydraulic Clutch

Explains how to check and correct the hydraulic clutch fluid level.

Changing the Hydraulic Clutch Fluid

Details the procedure for changing the hydraulic clutch fluid.

Changing the Hydraulic Clutch Fluid

Continues the procedure for changing hydraulic clutch fluid.

Brake System

Checking the Free Travel of the Hand Brake Lever

Explains how to check free travel of the hand brake lever.

Adjusting the Basic Position of the Hand Brake Lever

Guides on adjusting the hand brake lever position.

Checking the Brake Discs

Details how to check the brake discs for wear and damage.

Checking the Front Brake Fluid Level

Explains how to check the front brake fluid level.

Adding Front Brake Fluid

Guides on adding front brake fluid and related warnings.

Checking the Front Brake Linings

Explains how to check the thickness and condition of front brake linings.

Changing the Front Brake Linings

Guides on replacing the front brake linings.

Changing the Front Brake Linings

Continues the procedure for changing front brake linings.

Changing the Front Brake Linings

Continues the procedure for changing front brake linings.

Checking the Free Travel of Foot Brake Lever

Explains how to check free travel of the foot brake lever.

Adjusting the Basic Position of the Foot Brake Lever

Guides on adjusting the basic position of the foot brake lever.

Adjusting the Basic Position of the Foot Brake Lever

Continues the procedure for adjusting the foot brake lever.

Checking the Rear Brake Fluid Level

Explains how to check the rear brake fluid level.

Adding Rear Brake Fluid

Guides on adding rear brake fluid and related warnings.

Checking the Brake Linings of the Rear Brake

Explains how to check rear brake linings.

Changing the Rear Brake Linings

Guides on replacing the rear brake linings.

Changing the Rear Brake Linings

Continues the procedure for changing rear brake linings.

Changing the Rear Brake Linings

Continues the procedure for changing rear brake linings.

Wheels, Tires

Removing the Front Wheel

Provides instructions for removing the front wheel.

Installing the Front Wheel

Details how to install the front wheel.

Removing the Rear Wheel

Guides on removing the rear wheel.

Installing the Rear Wheel

Details how to install the rear wheel.

Checking the Tire Condition

Explains how to check tire condition, including cuts and age.

Checking Tire Pressure

Guides on checking and setting correct tire pressure.

Checking the Spoke Tension

Details how to check and correct spoke tension for wheel integrity.

Electrical System

Removing the 12-V Battery

Provides instructions for removing the 12-V battery.

Installing the 12-V Battery

Details how to install the 12-V battery correctly.

Charging the 12-V Battery

Guides on safely charging the 12-V battery.

Charging the 12-V Battery

Continues charging instructions and battery charger specifications.

Changing the Main Fuse

Provides instructions and warnings for changing the main fuse.

Changing the Main Fuse

Continues instructions for changing the main fuse.

Changing the Fuse of the Fuel Pump

Guides on changing the fuel pump fuse.

Diagnostics Connector

Indicates the location of the diagnostics connector.

Cooling System

Provides a general overview of the cooling system and its components.

Checking the Antifreeze and Coolant Level

Explains how to check antifreeze and coolant levels with warnings.

Checking the Coolant Level

Guides on checking the coolant level in the radiator.

Draining the Coolant

Provides instructions and warnings for draining the coolant.

Draining the Coolant

Continues the procedure for draining the coolant.

Refilling with Coolant

Details how to refill the cooling system with coolant.

Changing the Coolant

Guides on changing the coolant in the cooling system.

Tuning the Engine

Checking the Play in the Throttle Cable

Explains how to check throttle cable play and related adjustments.

Adjusting the Play in the Throttle Cable

Guides on adjusting throttle cable play and cable routing.

Adjusting the Play in the Throttle Cable

Continues adjusting throttle cable play.

Adjusting the Characteristic Map of the Throttle Response

Explains how to change the throttle response map using guide plates.

Adjusting the Characteristic Map of the Throttle Response

Continues explaining throttle response map adjustment.

Changing the Mapping

Guides on changing engine mapping using the combination switch.

Adjusting the Idle Speed

Explains how to adjust the engine's idle speed.

Adjusting the Idle Speed

Continues adjusting idle speed and programming throttle valve position.

Programming the Throttle Valve Position

Explains how to reprogram the throttle valve position.

Checking the Basic Position of the Shift Lever

Guides on checking the shift lever's basic position relative to boot.

Adjusting the Basic Position of the Shift Lever

Details how to adjust the shift lever's basic position.

Service Work on the Engine

Changing the Fuel Screen

Provides instructions for changing the fuel screen.

Checking the Engine Oil Level

Explains how to check the engine oil level at different temperatures.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screen

Guides on changing engine oil, filter, and cleaning the oil screen.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screen

Continues the procedure for oil change and filter cleaning.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screen

Continues the procedure for oil change and filter cleaning.

Adding Engine Oil

Guides on adding engine oil and using the correct type.

Adding Engine Oil

Continues the procedure for adding engine oil.

Cleaning, Care

Cleaning the Motorcycle

Provides instructions and warnings for cleaning the motorcycle.

Cleaning the Motorcycle

Continues cleaning instructions, including lubrication and surface care.

Storage

Provides comprehensive steps for storing the motorcycle for extended periods.

Storage

Continues storage instructions, including material recommendations.

Putting into Operation After Storage

Details the steps to put the motorcycle back into operation after storage.

Putting into Operation After Storage

Continues steps for bringing the motorcycle back to operational status.

Troubleshooting

Faults and Possible Causes

Lists common faults, their possible causes, and recommended actions.

Faults and Possible Causes

Continues listing common faults, causes, and actions.

Blink Code

Malfunction Indicator Lamp Codes

Lists blink codes for various malfunction conditions.

Malfunction Indicator Lamp Codes

Continues listing blink codes for malfunctions.

Technical Data

Engine Specifications

Provides detailed technical specifications for the engine.

Engine Tightening Torques

Lists torque specifications for various engine components.

Engine Tightening Torques

Continues engine component torque specifications.

Capacities

Lists capacities for engine oil, coolant, and fuel.

Chassis Specifications

Provides technical data for the chassis, frame, and suspension.

Chassis Specifications

Continues chassis specifications, including tire pressure and wheelbase.

Electrical System Specifications

Lists specifications for the battery, fuses, and instrument lighting.

Tire Specifications

Details tire sizes and types for specific models.

Fork Specifications (SX-F EU/AR)

Lists fork specifications including damping and oil capacity.

Fork Specifications (SX-F US)

Lists fork specifications including damping and oil capacity.

Fork Specifications (XC-F US)

Lists fork specifications for XC-F US model.

Shock Absorber Specifications (SX-F EU/AR)

Lists shock absorber specifications including damping and spring rates.

Chassis Tightening Torques

Lists torque specifications for chassis components.

Substances

Brake Fluid DOT 4 / DOT 5.1

Specifies requirements and recommended suppliers for brake fluid.

Coolant

Details requirements for coolant, including antifreeze protection.

Engine Oil (SAE 10W/50)

Specifies requirements and recommended suppliers for engine oil.

Fork Oil (SAE 4)

Specifies requirements for fork oil.

Shock Absorber Fluid (SAE 2.5)

Specifies requirements for shock absorber fluid.

Super Unleaded (ROZ 95) Fuel

Details requirements for super unleaded fuel, including ethanol content.

Auxiliary Substances

Air Filter Cleaner

Lists recommended supplier and product for air filter cleaning.

Chain Cleaner

Lists recommended supplier and product for chain cleaning.

Fuel Additive

Lists recommended supplier and product for fuel additive.

High Viscosity Grease

Lists recommended supplier and product for high viscosity grease.

Long-Life Grease

Lists recommended supplier and product for long-life grease.

Motorcycle Cleaner

Lists recommended supplier and product for motorcycle cleaner.

Off-road Chain Spray

Lists recommended supplier and product for off-road chain spray.

Oil for Foam Air Filter

Lists recommended supplier and product for foam air filter oil.

Preserving Materials for Paints, Metal and Rubber

Lists recommended supplier and product for preserving materials.

Silicone Spray

Lists recommended supplier and product for silicone spray.

Special Cleaner for Glossy and Matte Paint Finishes, Metal and Plastic Surfaces

Lists recommended supplier and product for special cleaner.

Special Grease (00062010053)

Lists recommended supplier and product for special grease.

Universal Oil Spray

Lists recommended supplier and product for universal oil spray.

Standards

JASO T903 MA2 Standard

Explains the JASO T903 MA2 standard for motorcycle engine oils.

SAE Standard

Explains the SAE viscosity classification system for oils.

Index of Special Terms

List of Abbreviations

List of Symbols

Yellow and Orange Symbols

Explains yellow/orange symbols indicating errors or active driving aids.

Green and Blue Symbols

Explains green/blue symbols indicating information or status.

White Symbols

Explains white symbols conveying general information.

Related product manuals

350 XC-F US KAILUB RUSSELL 2021

KTM 350 XC-F User Manual

Table of Contents

Other manuals for KTM 350 XC-F

Questions and Answers:

KTM 350 XC-F Specifications

Summary

Means of Representation

Symbols Used

Formats Used

Safety Advice

Use Definition – Intended Use

Misuse

Safety Advice

Degrees of Risk and Symbols

Tampering Warning

Safe Operation

Protective Clothing

Work Rules

Environment

Owner's Manual

Important Notes

Manufacturer Warranty, Implied Warranty

Fuel, Auxiliary Substances

Spare Parts, Technical Accessories

Service

Figures

Customer Service

View of Vehicle

View of Vehicle, Front Left (Example)

View of Vehicle, Rear Right (Example)

Serial Numbers

Vehicle Identification Number

Steering Head Label

Engine Number

Fork Article Number

Shock Absorber Article Number

Controls

Clutch Lever

Hand Brake Lever

Throttle Grip

Stop Button

Start Button

Combination Switch

Overview of Indicator Lights

Combination Instrument

Opening the Fuel Tank Filler Cap

Closing the Fuel Tank Filler Cap

Cold Start Button

Idle Speed Adjusting Screw

Shift Lever

Foot Brake Lever

Plug-in Stand (All SX-F Models)

Side Stand (XC-F US)

Preparing for Use

Advice on Preparing for First Use

Running in the Engine

Starting Power of Lithium-ion Batteries at Low Temperatures

Preparing for Difficult Operating Conditions

Preparing for Rides on Dry Sand

Preparing for Rides on Wet Sand

Preparing for Rides on Wet and Muddy Circuits

Preparing for High Temperatures or Slow Riding

Preparing for Low Temperatures or Snow

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Starting the Vehicle

Activating Launch Control

Activating Traction Control

Starting Off

Quickshifter (All SX-F Models)

Activating the Quickshifter (All SX-F Models)

Shifting, Riding

Applying the Brakes

Stopping, Parking

Transporting

Refueling

Refueling

Service Schedule

Additional Information

Service Schedule