Why does my KTM Motorcycle battery keep discharging?
If your KTM Motorcycle battery keeps discharging, the battery might not be charging. Check the charging voltage and the stator winding of the alternator. Also, check for any unwanted power consumers by checking the open-circuit current.
Why does my KTM 350 XC-F Motorcycle engine not turn on?
Several factors can prevent your KTM Motorcycle engine from turning on. These include: * **Operating error**: Ensure you are following the correct start procedure. * **Discharged battery**: Recharge the battery and check the charging voltage, open-circuit current and the alternator's stator winding. * **Blown main fuse**: Replace the main fuse. * **Defective starter relay**: Inspect the starter relay. * **Defective starter motor**: Examine the starter motor.
Why does my KTM Motorcycle engine have too little power?
If your KTM Motorcycle engine has too little power, several factors could be responsible. A very dirty air filter requires cleaning of the air filter and air filter box. A very dirty fuel filter needs replacement. A defect in the fuel injection system may be present, requiring a readout of the fault memory using the KTM diagnostics tool. The exhaust system might be leaky or deformed, or the main silencer may have too little glass fiber yarn filling, so check for damage and replace the glass fiber yarn filling if needed. Finally, insufficient valve clearance could be the cause, requiring adjustment.
Why does my KTM Motorcycle engine overheat?
If your KTM Motorcycle engine overheats, it could be due to several reasons. Check for coolant leaks and ensure the coolant level is correct. Insufficient airflow can also cause overheating, so switch off the engine when standing. Dirty radiator fins should be cleaned. Foam formation in the cooling system requires draining and refilling the coolant. Finally, inspect the radiator hose for bends and replace if necessary.
What to do if KTM 350 XC-F Motorcycle engine turns over but won't start?
If your KTM Motorcycle engine turns but doesn't start, check the following: ensure the fuel hose connection is properly joined. If the fuel screen in the fuel hose connection is clogged, replace it. Adjust the idle speed if it's not set correctly. Clean or replace oily or wet spark plugs, and adjust the plug gap to 0.8 mm (0.031 in) if it's too wide. Check the wiring harness for frayed short circuit cables and the electrical system for defects. Finally, a defect in the fuel injection system may require reading out the fault memory using the KTM diagnostics tool.
What to do if my KTM 350 XC-F Motorcycle has high oil consumption?
If your KTM Motorcycle is experiencing high oil consumption, check these: * Make sure the engine vent hose isn't bent; straighten it or replace if needed. * Verify that the engine oil level is not too high. * Consider that the engine oil might be too thin; in this case, change the oil and filter, and clean the oil screen. * Worn piston or cylinder; measure the piston/cylinder mounting clearance.
What to do if my KTM Motorcycle engine doesn't turn over?
If your KTM Motorcycle engine doesn't turn when you press the starter, possible causes include an operating error (ensure you're following the correct start procedure), a discharged battery (charge, check voltage, quiescent current, and stator winding), a blown main fuse (replace it), a defective starter relay (check it), or a defective starter motor (check it).
What to do if my KTM 350 XC-F Motorcycle engine overheats?
If your KTM Motorcycle engine is overheating, consider the following: * Check for coolant leaks and ensure the coolant level is correct. * When stationary, switch off the engine to prevent insufficient airflow. * Clean any dirt from the radiator fins. * Address foam formation by draining and refilling the coolant. * Inspect and replace any bent radiator hoses.
What to do if the KTM Motorcycle engine does not turn when the starter button is pressed?
If your KTM Motorcycle engine doesn't turn when you press the starter, it could be due to several reasons. You might not be following the correct start procedure. The battery could be discharged, requiring a recharge, voltage check, quiescent current check, and stator winding inspection. The main fuse might be blown, necessitating a replacement. Alternatively, the starter relay or the starter motor itself could be defective, requiring a check.
What to do if my KTM Motorcycle engine dies while riding?
If your KTM Motorcycle engine dies during the trip, the cause might be a lack of fuel, so refuel.
Explains the meaning of various symbols used in the manual.
Explains the typographical formats used throughout the document.
Defines the intended purpose and usage of the vehicle.
Describes improper uses of the vehicle and potential dangers.
Provides general safety instructions and warnings.
Explains hazard symbols and their associated risk levels.
Warns against unauthorized modifications to the noise control system.
Provides guidelines for safe operation, including dangers of accidents and poisoning.
Emphasizes the importance of wearing appropriate protective clothing.
Outlines general rules to follow when performing work on the vehicle.
Advises on responsible use and disposal of materials for environmental protection.
Stresses the importance of reading and understanding the manual.
Explains warranty conditions and exclusions for service work.
Details requirements for fuel and auxiliary substances.
Recommends using approved parts and accessories for safety.
Highlights the importance of proper service for vehicle longevity and performance.
Notes that figures may depict special equipment and may not show full disassembly.
Directs users to authorized dealers for questions and support.
Illustrates and labels components on the front left side of the vehicle.
Illustrates and labels components on the rear right side of the vehicle.
Shows where to find the vehicle identification number (VIN).
Indicates the location of the steering head label.
Shows where to find the engine number.
Shows where to find the article number for the fork.
Shows where to find the article number for the shock absorber.
Describes the clutch lever location and operation.
Describes the hand brake lever location and function.
Describes the throttle grip location and function.
Explains the location and states of the stop button.
Describes the start button location and its possible states.
Details the combination switch functions and mapping options.
Explains the meaning of various indicator lamps on the vehicle.
Describes the combination instrument and its display functions.
Provides instructions and safety warnings for opening the fuel tank cap.
Provides instructions for closing the fuel tank filler cap.
Explains the function and operation of the cold start button.
Details how to adjust the idle speed using the adjusting screw.
Shows gear positions and neutral for SX-F and XC-F models.
Describes the location and use of the foot brake lever.
Explains the use of the plug-in stand for parking and transport.
Describes the use and securing of the side stand.
Covers safety advice, clothing, and initial checks before riding.
Provides guidelines for the engine break-in period.
Explains starting procedures for lithium-ion batteries in cold conditions.
Advises on pre-ride checks for various challenging conditions.
Details preparations for riding on dry sand, including air filter covers.
Outlines preparations for riding on wet sand.
Details preparations for riding on wet and muddy circuits.
Advises on preparations for hot conditions or slow riding.
Details preparations for riding in cold conditions or snow.
Lists pre-ride checks for safety and operation.
Provides instructions and safety warnings for starting the engine.
Explains how to activate launch control for optimal acceleration.
Describes how to activate and use traction control.
Provides instructions for moving off from a standstill.
Explains the function and activation of the quickshifter.
Details the procedure for activating the quickshifter.
Guides on gear shifting and general riding techniques.
Provides instructions and warnings on brake application.
Explains procedures for stopping and parking the motorcycle safely.
Provides guidance on transporting the motorcycle securely.
Details safety precautions and procedures for refueling.
Continues refueling instructions, including fuel types and tank capacity.
Explains how service intervals may vary by country and conditions.
Presents a schedule of maintenance tasks and their intervals.
Explains how to adjust chassis settings based on rider weight.
Describes the WP XACT air suspension system used in the fork.
Explains high-speed and low-speed compression damping.
Provides steps to adjust low-speed compression damping on the shock absorber.
Guides on adjusting high-speed compression damping on the shock absorber.
Provides instructions for adjusting rebound damping on the shock absorber.
Details how to measure rear wheel dimension without load.
Explains how to check static sag of the shock absorber.
Explains how to check riding sag of the shock absorber.
Guides on adjusting the spring preload for optimal suspension.
Provides steps to adjust spring preload on the shock absorber.
Details how to adjust the riding sag for the shock absorber.
Explains how to check the basic settings of the front fork.
Guides on adjusting air pressure in the front fork suspension.
Explains how to adjust compression damping on the front fork.
Guides on adjusting rebound damping on the front fork.
Explains handlebar mounting positions and adjustments.
Provides steps for adjusting the handlebar position.
Details procedures for safely lifting the motorcycle on a stand.
Explains how to safely remove the motorcycle from a lift stand.
Provides instructions for bleeding air from the fork legs.
Details how to clean dust boots on the fork legs.
Guides on removing the fork protector.
Details how to install the fork protector.
Provides instructions for removing the front fork legs.
Details how to install the front fork legs correctly.
Guides on removing the lower triple clamp assembly.
Details the installation of the lower triple clamp assembly.
Explains how to check for play in the steering head bearings.
Guides on adjusting the steering head bearing play.
Describes the process of lubricating the steering head bearing.
Guides on removing the front start number plate.
Details how to install the front start number plate.
Provides instructions for removing the front fender.
Details how to install the front fender.
Guides on removing the rear shock absorber.
Details how to install the rear shock absorber.
Continues installation steps for the rear shock absorber.
Guides on removing the motorcycle seat.
Details how to install the motorcycle seat.
Guides on removing the air filter box cover.
Details how to install the air filter box cover.
Guides on removing the air filter.
Details how to clean the air filter and its box.
Details how to install the air filter correctly.
Guides on preparing the air filter box cover for securing.
Provides instructions for removing the main silencer.
Details how to install the main silencer.
Guides on replacing the glass fiber yarn filling in the silencer.
Provides instructions for removing the fuel tank.
Details how to install the fuel tank.
Explains how to check the chain for dirt buildup.
Provides instructions and warnings for cleaning the motorcycle chain.
Guides on how to check and set the correct chain tension.
Details the procedure for adjusting the chain tension.
Guides on checking wear of chain, sprockets, and chain guide.
Explains how to check the frame for damage or deformation.
Guides on checking the link fork for damage or cracking.
Details how to check the routing of throttle cables.
Guides on checking handlebar rubber grips for wear and damage.
Explains how to reprogram the quickshifter if performance decreases.
Guides on adjusting the clutch lever position for hand size.
Explains how to check and correct the hydraulic clutch fluid level.
Details the procedure for changing the hydraulic clutch fluid.
Continues the procedure for changing hydraulic clutch fluid.
Explains how to check free travel of the hand brake lever.
Guides on adjusting the hand brake lever position.
Details how to check the brake discs for wear and damage.
Explains how to check the front brake fluid level.
Guides on adding front brake fluid and related warnings.
Explains how to check the thickness and condition of front brake linings.
Guides on replacing the front brake linings.
Continues the procedure for changing front brake linings.
Continues the procedure for changing front brake linings.
Explains how to check free travel of the foot brake lever.
Guides on adjusting the basic position of the foot brake lever.
Continues the procedure for adjusting the foot brake lever.
Explains how to check the rear brake fluid level.
Guides on adding rear brake fluid and related warnings.
Explains how to check rear brake linings.
Guides on replacing the rear brake linings.
Continues the procedure for changing rear brake linings.
Continues the procedure for changing rear brake linings.
Provides instructions for removing the front wheel.
Details how to install the front wheel.
Guides on removing the rear wheel.
Details how to install the rear wheel.
Explains how to check tire condition, including cuts and age.
Guides on checking and setting correct tire pressure.
Details how to check and correct spoke tension for wheel integrity.
Provides instructions for removing the 12-V battery.
Details how to install the 12-V battery correctly.
Guides on safely charging the 12-V battery.
Continues charging instructions and battery charger specifications.
Provides instructions and warnings for changing the main fuse.
Continues instructions for changing the main fuse.
Guides on changing the fuel pump fuse.
Indicates the location of the diagnostics connector.
Provides a general overview of the cooling system and its components.
Explains how to check antifreeze and coolant levels with warnings.
Guides on checking the coolant level in the radiator.
Provides instructions and warnings for draining the coolant.
Continues the procedure for draining the coolant.
Details how to refill the cooling system with coolant.
Guides on changing the coolant in the cooling system.
Explains how to check throttle cable play and related adjustments.
Guides on adjusting throttle cable play and cable routing.
Continues adjusting throttle cable play.
Explains how to change the throttle response map using guide plates.
Continues explaining throttle response map adjustment.
Guides on changing engine mapping using the combination switch.
Explains how to adjust the engine's idle speed.
Continues adjusting idle speed and programming throttle valve position.
Explains how to reprogram the throttle valve position.
Guides on checking the shift lever's basic position relative to boot.
Details how to adjust the shift lever's basic position.
Provides instructions for changing the fuel screen.
Explains how to check the engine oil level at different temperatures.
Guides on changing engine oil, filter, and cleaning the oil screen.
Continues the procedure for oil change and filter cleaning.
Continues the procedure for oil change and filter cleaning.
Guides on adding engine oil and using the correct type.
Continues the procedure for adding engine oil.
Provides instructions and warnings for cleaning the motorcycle.
Continues cleaning instructions, including lubrication and surface care.
Provides comprehensive steps for storing the motorcycle for extended periods.
Continues storage instructions, including material recommendations.
Details the steps to put the motorcycle back into operation after storage.
Continues steps for bringing the motorcycle back to operational status.
Lists common faults, their possible causes, and recommended actions.
Continues listing common faults, causes, and actions.
Lists blink codes for various malfunction conditions.
Continues listing blink codes for malfunctions.
Provides detailed technical specifications for the engine.
Lists torque specifications for various engine components.
Continues engine component torque specifications.
Lists capacities for engine oil, coolant, and fuel.
Provides technical data for the chassis, frame, and suspension.
Continues chassis specifications, including tire pressure and wheelbase.
Lists specifications for the battery, fuses, and instrument lighting.
Details tire sizes and types for specific models.
Lists fork specifications including damping and oil capacity.
Lists fork specifications including damping and oil capacity.
Lists fork specifications for XC-F US model.
Lists shock absorber specifications including damping and spring rates.
Lists torque specifications for chassis components.
Specifies requirements and recommended suppliers for brake fluid.
Details requirements for coolant, including antifreeze protection.
Specifies requirements and recommended suppliers for engine oil.
Specifies requirements for fork oil.
Specifies requirements for shock absorber fluid.
Details requirements for super unleaded fuel, including ethanol content.
Lists recommended supplier and product for air filter cleaning.
Lists recommended supplier and product for chain cleaning.
Lists recommended supplier and product for fuel additive.
Lists recommended supplier and product for high viscosity grease.
Lists recommended supplier and product for long-life grease.
Lists recommended supplier and product for motorcycle cleaner.
Lists recommended supplier and product for off-road chain spray.
Lists recommended supplier and product for foam air filter oil.
Lists recommended supplier and product for preserving materials.
Lists recommended supplier and product for silicone spray.
Lists recommended supplier and product for special cleaner.
Lists recommended supplier and product for special grease.
Lists recommended supplier and product for universal oil spray.
Explains the JASO T903 MA2 standard for motorcycle engine oils.
Explains the SAE viscosity classification system for oils.
Explains yellow/orange symbols indicating errors or active driving aids.
Explains green/blue symbols indicating information or status.
Explains white symbols conveying general information.
Explains the meaning of various symbols used in the manual.
Explains the typographical formats used throughout the document.
Defines the intended purpose and usage of the vehicle.
Describes improper uses of the vehicle and potential dangers.
Provides general safety instructions and warnings.
Explains hazard symbols and their associated risk levels.
Warns against unauthorized modifications to the noise control system.
Provides guidelines for safe operation, including dangers of accidents and poisoning.
Emphasizes the importance of wearing appropriate protective clothing.
Outlines general rules to follow when performing work on the vehicle.
Advises on responsible use and disposal of materials for environmental protection.
Stresses the importance of reading and understanding the manual.
Explains warranty conditions and exclusions for service work.
Details requirements for fuel and auxiliary substances.
Recommends using approved parts and accessories for safety.
Highlights the importance of proper service for vehicle longevity and performance.
Notes that figures may depict special equipment and may not show full disassembly.
Directs users to authorized dealers for questions and support.
Illustrates and labels components on the front left side of the vehicle.
Illustrates and labels components on the rear right side of the vehicle.
Shows where to find the vehicle identification number (VIN).
Indicates the location of the steering head label.
Shows where to find the engine number.
Shows where to find the article number for the fork.
Shows where to find the article number for the shock absorber.
Describes the clutch lever location and operation.
Describes the hand brake lever location and function.
Describes the throttle grip location and function.
Explains the location and states of the stop button.
Describes the start button location and its possible states.
Details the combination switch functions and mapping options.
Explains the meaning of various indicator lamps on the vehicle.
Describes the combination instrument and its display functions.
Provides instructions and safety warnings for opening the fuel tank cap.
Provides instructions for closing the fuel tank filler cap.
Explains the function and operation of the cold start button.
Details how to adjust the idle speed using the adjusting screw.
Shows gear positions and neutral for SX-F and XC-F models.
Describes the location and use of the foot brake lever.
Explains the use of the plug-in stand for parking and transport.
Describes the use and securing of the side stand.
Covers safety advice, clothing, and initial checks before riding.
Provides guidelines for the engine break-in period.
Explains starting procedures for lithium-ion batteries in cold conditions.
Advises on pre-ride checks for various challenging conditions.
Details preparations for riding on dry sand, including air filter covers.
Outlines preparations for riding on wet sand.
Details preparations for riding on wet and muddy circuits.
Advises on preparations for hot conditions or slow riding.
Details preparations for riding in cold conditions or snow.
Lists pre-ride checks for safety and operation.
Provides instructions and safety warnings for starting the engine.
Explains how to activate launch control for optimal acceleration.
Describes how to activate and use traction control.
Provides instructions for moving off from a standstill.
Explains the function and activation of the quickshifter.
Details the procedure for activating the quickshifter.
Guides on gear shifting and general riding techniques.
Provides instructions and warnings on brake application.
Explains procedures for stopping and parking the motorcycle safely.
Provides guidance on transporting the motorcycle securely.
Details safety precautions and procedures for refueling.
Continues refueling instructions, including fuel types and tank capacity.
Explains how service intervals may vary by country and conditions.
Presents a schedule of maintenance tasks and their intervals.
Explains how to adjust chassis settings based on rider weight.
Describes the WP XACT air suspension system used in the fork.
Explains high-speed and low-speed compression damping.
Provides steps to adjust low-speed compression damping on the shock absorber.
Guides on adjusting high-speed compression damping on the shock absorber.
Provides instructions for adjusting rebound damping on the shock absorber.
Details how to measure rear wheel dimension without load.
Explains how to check static sag of the shock absorber.
Explains how to check riding sag of the shock absorber.
Guides on adjusting the spring preload for optimal suspension.
Provides steps to adjust spring preload on the shock absorber.
Details how to adjust the riding sag for the shock absorber.
Explains how to check the basic settings of the front fork.
Guides on adjusting air pressure in the front fork suspension.
Explains how to adjust compression damping on the front fork.
Guides on adjusting rebound damping on the front fork.
Explains handlebar mounting positions and adjustments.
Provides steps for adjusting the handlebar position.
Details procedures for safely lifting the motorcycle on a stand.
Explains how to safely remove the motorcycle from a lift stand.
Provides instructions for bleeding air from the fork legs.
Details how to clean dust boots on the fork legs.
Guides on removing the fork protector.
Details how to install the fork protector.
Provides instructions for removing the front fork legs.
Details how to install the front fork legs correctly.
Guides on removing the lower triple clamp assembly.
Details the installation of the lower triple clamp assembly.
Explains how to check for play in the steering head bearings.
Guides on adjusting the steering head bearing play.
Describes the process of lubricating the steering head bearing.
Guides on removing the front start number plate.
Details how to install the front start number plate.
Provides instructions for removing the front fender.
Details how to install the front fender.
Guides on removing the rear shock absorber.
Details how to install the rear shock absorber.
Continues installation steps for the rear shock absorber.
Guides on removing the motorcycle seat.
Details how to install the motorcycle seat.
Guides on removing the air filter box cover.
Details how to install the air filter box cover.
Guides on removing the air filter.
Details how to clean the air filter and its box.
Details how to install the air filter correctly.
Guides on preparing the air filter box cover for securing.
Provides instructions for removing the main silencer.
Details how to install the main silencer.
Guides on replacing the glass fiber yarn filling in the silencer.
Provides instructions for removing the fuel tank.
Details how to install the fuel tank.
Explains how to check the chain for dirt buildup.
Provides instructions and warnings for cleaning the motorcycle chain.
Guides on how to check and set the correct chain tension.
Details the procedure for adjusting the chain tension.
Guides on checking wear of chain, sprockets, and chain guide.
Explains how to check the frame for damage or deformation.
Guides on checking the link fork for damage or cracking.
Details how to check the routing of throttle cables.
Guides on checking handlebar rubber grips for wear and damage.
Explains how to reprogram the quickshifter if performance decreases.
Guides on adjusting the clutch lever position for hand size.
Explains how to check and correct the hydraulic clutch fluid level.
Details the procedure for changing the hydraulic clutch fluid.
Continues the procedure for changing hydraulic clutch fluid.
Explains how to check free travel of the hand brake lever.
Guides on adjusting the hand brake lever position.
Details how to check the brake discs for wear and damage.
Explains how to check the front brake fluid level.
Guides on adding front brake fluid and related warnings.
Explains how to check the thickness and condition of front brake linings.
Guides on replacing the front brake linings.
Continues the procedure for changing front brake linings.
Continues the procedure for changing front brake linings.
Explains how to check free travel of the foot brake lever.
Guides on adjusting the basic position of the foot brake lever.
Continues the procedure for adjusting the foot brake lever.
Explains how to check the rear brake fluid level.
Guides on adding rear brake fluid and related warnings.
Explains how to check rear brake linings.
Guides on replacing the rear brake linings.
Continues the procedure for changing rear brake linings.
Continues the procedure for changing rear brake linings.
Provides instructions for removing the front wheel.
Details how to install the front wheel.
Guides on removing the rear wheel.
Details how to install the rear wheel.
Explains how to check tire condition, including cuts and age.
Guides on checking and setting correct tire pressure.
Details how to check and correct spoke tension for wheel integrity.
Provides instructions for removing the 12-V battery.
Details how to install the 12-V battery correctly.
Guides on safely charging the 12-V battery.
Continues charging instructions and battery charger specifications.
Provides instructions and warnings for changing the main fuse.
Continues instructions for changing the main fuse.
Guides on changing the fuel pump fuse.
Indicates the location of the diagnostics connector.
Provides a general overview of the cooling system and its components.
Explains how to check antifreeze and coolant levels with warnings.
Guides on checking the coolant level in the radiator.
Provides instructions and warnings for draining the coolant.
Continues the procedure for draining the coolant.
Details how to refill the cooling system with coolant.
Guides on changing the coolant in the cooling system.
Explains how to check throttle cable play and related adjustments.
Guides on adjusting throttle cable play and cable routing.
Continues adjusting throttle cable play.
Explains how to change the throttle response map using guide plates.
Continues explaining throttle response map adjustment.
Guides on changing engine mapping using the combination switch.
Explains how to adjust the engine's idle speed.
Continues adjusting idle speed and programming throttle valve position.
Explains how to reprogram the throttle valve position.
Guides on checking the shift lever's basic position relative to boot.
Details how to adjust the shift lever's basic position.
Provides instructions for changing the fuel screen.
Explains how to check the engine oil level at different temperatures.
Guides on changing engine oil, filter, and cleaning the oil screen.
Continues the procedure for oil change and filter cleaning.
Continues the procedure for oil change and filter cleaning.
Guides on adding engine oil and using the correct type.
Continues the procedure for adding engine oil.
Provides instructions and warnings for cleaning the motorcycle.
Continues cleaning instructions, including lubrication and surface care.
Provides comprehensive steps for storing the motorcycle for extended periods.
Continues storage instructions, including material recommendations.
Details the steps to put the motorcycle back into operation after storage.
Continues steps for bringing the motorcycle back to operational status.
Lists common faults, their possible causes, and recommended actions.
Continues listing common faults, causes, and actions.
Lists blink codes for various malfunction conditions.
Continues listing blink codes for malfunctions.
Provides detailed technical specifications for the engine.
Lists torque specifications for various engine components.
Continues engine component torque specifications.
Lists capacities for engine oil, coolant, and fuel.
Provides technical data for the chassis, frame, and suspension.
Continues chassis specifications, including tire pressure and wheelbase.
Lists specifications for the battery, fuses, and instrument lighting.
Details tire sizes and types for specific models.
Lists fork specifications including damping and oil capacity.
Lists fork specifications including damping and oil capacity.
Lists fork specifications for XC-F US model.
Lists shock absorber specifications including damping and spring rates.
Lists torque specifications for chassis components.
Specifies requirements and recommended suppliers for brake fluid.
Details requirements for coolant, including antifreeze protection.
Specifies requirements and recommended suppliers for engine oil.
Specifies requirements for fork oil.
Specifies requirements for shock absorber fluid.
Details requirements for super unleaded fuel, including ethanol content.
Lists recommended supplier and product for air filter cleaning.
Lists recommended supplier and product for chain cleaning.
Lists recommended supplier and product for fuel additive.
Lists recommended supplier and product for high viscosity grease.
Lists recommended supplier and product for long-life grease.
Lists recommended supplier and product for motorcycle cleaner.
Lists recommended supplier and product for off-road chain spray.
Lists recommended supplier and product for foam air filter oil.
Lists recommended supplier and product for preserving materials.
Lists recommended supplier and product for silicone spray.
Lists recommended supplier and product for special cleaner.
Lists recommended supplier and product for special grease.
Lists recommended supplier and product for universal oil spray.
Explains the JASO T903 MA2 standard for motorcycle engine oils.
Explains the SAE viscosity classification system for oils.
Explains yellow/orange symbols indicating errors or active driving aids.
Explains green/blue symbols indicating information or status.
Explains white symbols conveying general information.
General| Displacement | 349.7 cc |
|---|---|
| Bore/Stroke | 88 mm / 57.5 mm |
| Starter | Electric starter |
| Transmission | 6-speed |
| Cooling | Liquid cooled |
| Front Suspension | WP XACT-USD, Ø 48 mm |
| Rear Suspension | WP XACT Monoshock with linkage |
| Ground Clearance | 370 mm |
| Engine Type | Single-cylinder, 4-stroke |
| Fuel System | Keihin EFI, 44 mm Throttle Body |
| Frame | Central double-cradle type, 25CrMo4 steel |
| Front Brake | Disc brake, 260 mm |
| Rear Brake | Disc brake, 220 mm |
| Fuel Tank Capacity | 8.5 liters |
To Next Page
