Why does my Kubota ZG127E-AU discharge chute plug?
A plugged discharge chute on your Kubota Lawn Mower can be caused by grass that is too wet (wait for grass to dry), grass that is too long (raise cutting height and cut grass twice), cutting too low (raise cutting height), engine rpm too low (mow at full throttle), or ground speed too fast (slow down).
What causes streaking of grass uncut with Kubota ZG127E-AU?
Streaking of uncut grass with your Kubota Lawn Mower can occur if the ground speed is too fast (slow down), the engine rpm is too low (mow at full throttle, check and reset engine rpm), the grass is too long (cut grass twice), the blades are dull or damaged (replace blades or have blades sharpened), or there is debris in the mower deck (clean mower deck).
Why does my Kubota Lawn Mower vibrate excessively?
Excessive vibration in your Kubota Lawn Mower can be caused by debris on the mower deck or in the pulleys (clean mower deck and pulleys), a damaged mower belt (replace mower belt), damaged pulleys (replace pulleys), or blades out of balance (have blades balanced).
Why does my Kubota ZG127E-AU Lawn Mower load down the machine?
If your Kubota Lawn Mower loads down the machine, it could be because the engine rpm is too low (mow at full throttle, check and reset engine rpm), the ground speed is too fast (slow down), or debris is wrapped around mower spindles (clean mower).
Why won't my Kubota ZG127E-AU Lawn Mower starter function?
If your Kubota Lawn Mower starter does not function, it could be due to a battery overused until lights are dim (charge battery sufficiently), a poor terminal connection (clean the terminal and tighten securely), or the battery life expired (replace battery).
General| Brand | Kubota |
|---|---|
| Model | ZG127E-AU |
| Category | Lawn Mower |
| Language | English |
Safety checks and preparations before starting the machine.
Guidelines for safe operation practices and awareness of hazards.
Specific precautions concerning children around the operating machine.
Precautions for operating on inclines to prevent tip-overs and loss of control.
Procedures for safely stopping the engine and parking the machine.
Safety guidelines for transporting the machine on a trailer or truck.
Safety precautions during maintenance, refueling, and storing the machine.
Locating and recording machine, ROPS, engine, and mower serial numbers.
Technical details of the engine, including displacement, bore, stroke, and cooling.
Physical dimensions, weight, and fluid capacities of the machine.
Specifications for traveling speeds, steering, transmission, and turning radius.
Technical specifications for the mower deck, including cutting width and blade details.
Maximum loading weight limits for front axle, rear axle, and total machine weight.
Identification and location of various controls and indicators on the instrument panel.
Step-by-step instructions for attaching the mower deck to the machine.
Procedures for adjusting the mower deck and anti-scalp rollers after mounting.
Procedures for removing the mower deck from the machine.
Step-by-step instructions for starting the engine safely.
Safe practices for mounting and dismounting the machine.
Checks to perform while the engine is running to ensure normal operation.
Specific starting procedures for cold weather conditions.
Procedures for warming up the engine and transmission oil, especially in low temperatures.
Instructions for safely jump starting the engine using a booster vehicle.
Procedures for safely shutting off the engine.
Essential checks to perform before starting the machine daily.
Maintenance tasks required every 25 operating hours.
Maintenance tasks required every 50 operating hours.
Maintenance tasks required every 100 operating hours.
Maintenance tasks required every 200 operating hours.
Maintenance tasks required every 400 operating hours.
Maintenance tasks required every 500 operating hours.
Maintenance tasks required annually.
Maintenance tasks required every two years.
Maintenance tasks performed as needed.
Information on types, quantities, and specifications of lubricants and fuel.
Procedures for adjusting motion control levers, including HST neutral and alignment.
Procedures for leveling the mower deck side-to-side and front-to-rear.
Steps to prepare the machine for storage, including cleaning and fluid checks.
Steps to prepare the machine for operation after it has been stored.
Diagnosing and resolving common engine starting and running problems.
Diagnosing and resolving issues related to the battery and starting system.
Diagnosing and resolving general machine operational problems.
Diagnosing and resolving problems related to the mower deck's performance.
To Next Page
