What to do if the torque limiter disengages frequently on my KUHN Farm Equipment?
If the torque limiter on your KUHN Farm Equipment frequently disengages, it could be due to a high load on the tine arms. Try adjusting the wheel height. Alternatively, reduce the ground speed.
Why is there crop pick up at the rear of the rotor on my KUHN GA4121GM?
If you notice crop pick up at the rear of the rotor on your KUHN Farm Equipment, there are several potential causes: * The swaths may be too compact between the tines and swath screen. Increase the swath screen distance. * There may be earth clods on the tines. Adjust the wheel height. * The rotor speed might be too high. Reduce the PTO speed.
How to fix poor raking over the whole rotor width on KUHN GA4121GM Farm Equipment?
To address poor raking over the whole rotor width on your KUHN Farm Equipment, the tines may be too far from the ground. Adjust the wheel height to correct this.
Why is my KUHN GA4121GM Farm Equipment rotor vibrating unusually?
If you're experiencing unusual rotor vibrations with your KUHN Farm Equipment, the rotor speed may be too high. Check the PTO speed and ensure it's at a maximum of 540 min-1.
What to do if crop is ejecting at the front of the swath screen on my KUHN GA4121GM Farm Equipment?
If your KUHN Farm Equipment is ejecting crop at the front of the swath screen, it could be due to an incorrect swath screen position, specifically being too much at the rear. Move the swath screen forwards. You may also need to reduce the PTO speed.
How to fix poor raking on one side of the rotor on KUHN GA4121GM Farm Equipment?
If you're experiencing poor raking on one side of the rotor with your KUHN Farm Equipment, it could be that the rotor is tilted towards the opposite side. To fix this, adjust the wheel height to achieve the same tine-to-soil distance on both sides of the machine.
Why is crop ejecting underneath the swath screen on my KUHN GA4121GM?
If you're experiencing crop ejection underneath the swath screen on your KUHN Farm Equipment, it's likely that the swath screen position is incorrect, being too far away from the ground. Move the swath screen downwards to resolve this issue.
How to resolve poor raking on both sides when using KUHN Farm Equipment?
If you're experiencing poor raking on the two sides with your KUHN Farm Equipment, the rotor might be tilted frontward. You can lengthen the top link or adjust the wheel height to correct this.
What causes poor raking in the middle when using KUHN Farm Equipment?
If you're experiencing poor raking in the middle with your KUHN Farm Equipment, it could be that the rotor is tilted rearwards. Shorten the top link to resolve this issue.
Company reserves the right to make improvements or changes to products without prior obligation.
Service life of wear parts depends on usage conditions like soil, weather, etc.
Machine is designed for raking and forming windrows of pre-mowed fodder and straw.
Illustrations may be based on one machine type; instructions apply to all covered machines.
Diagram showing the front view of the Gyrorake machine.
Diagram showing the rear view of the Gyrorake machine.
Information on the machine's identification plate for type and serial number.
List of optional equipment that can be fitted to the machine.
Explanation of hazard, caution, and information symbols used in the manual.
General safety guidelines and precautions for operating the machine.
Diagram showing locations and explanations of safety decals on the machine.
Glossary of machine parts and components with numerical references.
Detailed technical data including dimensions, weight, power, and PTO speed.
Information on factory-fitted equipment and required PTO shafts.
Measured sound pressure levels for tractor and tractor with machine.
Instructions for connecting and disconnecting the machine from the tractor.
Procedure for greasing, connecting, and adjusting the PTO shaft.
Steps for safely disconnecting the machine from the tractor.
Procedure for folding the machine into its transport configuration.
Ensuring compliance with highway codes for road transport.
Steps to deploy the machine from transport to working configuration.
Adjustments required for optimal performance in working conditions.
Guidelines for operating the machine safely and effectively.
Details on the front support wheel for improved ground contour adaptation.
Information on bogie axles for improved machine flotation on uneven ground.
Details on the hydraulic windrow curtain for adjusting windrow width.
Details on rear lighting and signalling components for European road regulations.
Chart indicating maintenance and lubrication intervals based on usage hours.
Detailed lubrication instructions and points for the machine's components.
General maintenance procedures for the machine.
Instructions for storing the machine at the end and start of the season.
General| Brand | KUHN |
|---|---|
| Model | GA4121GM |
| Category | Farm Equipment |
| Language | English |
To Next Page
