EasyManua.ls Logo

KUHN GMD 800 G II - User Manual

KUHN GMD 800 G II
48 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ASSEMBLY / OPERATOR'S MANUAL
GMD 600 G II / 700 G II / 800 G II
GMD 600 G II-HD / 700 G II-HD / 800 G II-HD
MULTIDISC MOWER
N° 95009 D.GB - 06.2006

Table of Contents

Questions and Answers

  • J
    James JohnsonAug 8, 2025
    Why is my KUHN GMD 800 G II Farm Equipment leaving uneven stubble?
    • R
      ramseynancyAug 9, 2025
      Uneven stubble can occur for several reasons. It could be due to dull or broken knives, which require replacement. Ensure knives are installed correctly with the arrow on the upper face pointing in the disc's rotation direction. Check belts for correct tension if the disc speed is low. Increase engine speed to run the PTO at 540 rpm if the PTO speed is low. Finally, reduce tilt on the cutterbar if there is too much.
  • D
    dfrenchAug 14, 2025
    What to do if soil builds up in front of the KUHN Farm Equipment cutterbar?
    • D
      Dustin BennettAug 14, 2025
      Soil buildup in front of the cutterbar can be addressed by adjusting the compensating spring tension if there's too much cutterbar down pressure. If working in very wet conditions, adjust the main frame height by shortening the chain as needed. Consider fitting a set of raised skids.
  • K
    Kyle GonzalezAug 20, 2025
    Why KUHN Farm Equipment cutterbar is not floating?
    • G
      garyspearsAug 20, 2025
      If the cutterbar isn't floating, ensure the tractor spool valve is set to the float position, allowing the cylinder to move freely. Also, the compensating spring may need adjustment. Check the condition of the bevel gearbox mounting bushes and replace them if necessary, as wear or seizing can cause this issue.
  • D
    Dale RushAug 27, 2025
    What to do if KUHN GMD 800 G II Farm Equipment stubble is too long?
    • K
      kristinemillerAug 27, 2025
      If the stubble is too long, adjust the cutterbar angle using the tractor top link. You may also need to adjust the compensating spring tension and main frame height if there is insufficient cutterbar down pressure.
  • J
    Jamie GreeneSep 2, 2025
    Why is my KUHN Farm Equipment machine breaking back too easily?
    • R
      Robert WilliamsSep 2, 2025
      If the machine is breaking back too easily, it could be due to insufficient tension on the breakaway spring washers; tighten them. Alternatively, reduce the tractor's ground speed if it's excessive for the field conditions.

Summary

Safety and Precautions

Machine Usage and General Safety

Covers designated use, general recommendations, and basic safety principles.

Operational Safety (PTO, Hydraulics, Attachment)

Covers safe attachment, PTO, and hydraulic system operations.

Safety Decals and Maintenance

Machine Assembly

Fitting Break-away Latch and Chassis

Installing Belt Shields and Frame Pipe

Connecting Components and Guards

General Information and Tractor Adaptation

Tractor Hitch and Offset Adjustment

Details on adjusting lower links and positioning hitch pins for various tractor types.

PTO Shaft Connection

Transport and Working Position

Transporting the Mower

Setting Working Position

Mower Operation

Safe Operating Practices

Guidelines for safe operation, cutting height, and ground contour following.

Safety Break-away and Parking

Troubleshooting and Storage

Troubleshooting Guide

Common problems, their causes, and recommended remedies for the mower.

Sound Levels and Limited Warranty

Limited Warranty Information

Outlines the terms, conditions, and exclusions of the manufacturer's warranty.

KUHN GMD 800 G II Specifications

General IconGeneral
BrandKUHN
ModelGMD 800 G II
CategoryFarm Equipment
LanguageEnglish

Related product manuals