KUHN HR3504D - User Manual

Questions and Answers

S
Stephanie CochranAug 17, 2025
Why is there excessive power requirement for my KUHN Farm Equipment?
- R
  Robert VasquezAug 17, 2025
  Excessive power requirement in your KUHN Farm Equipment can stem from several factors. It may be caused by a working depth that's too deep, so reduce it using the roller. The rotor speed might be too high; reduce it by changing gearwheels in the gearbox, considering optional gearwheel sets. Also, excessive ground speed can contribute, so reduce it. Finally, check the rear leveling bar setting; raise or remove it if it's incorrectly set.
A
Alejandro WrightAug 20, 2025
What to do if my KUHN HR3504D Farm Equipment produces tilth that is too coarse?
- R
  Rebekah ReedAug 20, 2025
  If your KUHN Farm Equipment is producing tilth that is too coarse, several factors could be responsible. Check for considerable build-up of long plant residues around the blades and eliminate them. Ensure that your ground speed isn't excessive by reducing it. Also, the rotor speed may be too low; increase it by changing gearwheels in the gearbox, considering optional gearwheel sets. Finally, if there is no levelling bar, install one, preferably to the rear.
E
emily64Aug 22, 2025
What to do if my KUHN HR3504D Farm Equipment produces tilth that is too fine?
- A
  Adam SilvaAug 22, 2025
  If the tilth produced by your KUHN Farm Equipment is too fine, it could be due to several reasons. The rotor speed might be too high, so reduce it by changing gearwheels in the gearbox, considering optional gearwheel sets. Also, the forward speed may be too slow, so increase it. Check the rear levelling bar; if it is too low, raise or remove it.
J
Jeremy ArnoldAug 26, 2025
Why is my KUHN HR3504D Farm Equipment drive noisy during work?
- A
  Andrew LeonardAug 26, 2025
  A noisy drive during work with your KUHN Farm Equipment could be due to the machine being tilted excessively to the front or rear. Lengthen or shorten the top link to set the machine horizontally during work, ensuring the tractor PTO shaft end and machine input shaft are parallel. Insufficient machine side to side stabilization could also be a factor. Use lower linkage arm stabilizers to correct this.
J
James HolmesAug 28, 2025
How to fix incorrect packer roller functioning (clogging, jamming or soil build-up) on my KUHN Farm Equipment?
- I
  isabel03Aug 28, 2025
  If you're experiencing incorrect packer roller functioning, such as clogging, jamming, or soil build-up, with your KUHN Farm Equipment, start by checking the scraper plates. Make sure they are adjusted correctly. If the scrapers are jammed by trash, clean them by pivoting them rearwards. Also, ensure the scraper bar is in the furthest forward position. Wear compensation can only be obtained by sliding the scraper plates forward individually.
J
Jeffery RobertsAug 31, 2025
Why is my KUHN HR3504D Farm Equipment drive noisy when lifting the machine?
- N
  Nicole TaylorAug 31, 2025
  A noisy drive when lifting your KUHN Farm Equipment could be caused by a badly positioned or adjusted top link of the 3-point hitch; position the top link parallel to the lower linkage arms. It may also be caused by excessive lifting height, so limit the lift linkage stroke.
D
Dana WeissSep 2, 2025
How to prevent ridging at the side of my KUHN HR3504D Farm Equipment?
- K
  Krista MatthewsSep 2, 2025
  To prevent ridging at the side of your KUHN Farm Equipment, ensure that each anti-ridging plate is positioned as close as possible to the ground and roller on the side deflectors.
C
Carolyn ThomasSep 5, 2025
How to prevent clogging of the Maxicrumbler roller on my KUHN HR3504D Farm Equipment?
- A
  Ashley MartinezSep 5, 2025
  To prevent clogging of the Maxicrumbler roller on your KUHN Farm Equipment, consider that this may be due to wet conditions and too high load on the roller. In this case, use Packer PK2 roller or Maxipacker roller.
R
Ruth BoyerSep 8, 2025
How to prevent Crumbler roller clogging on my KUHN HR3504D Farm Equipment?
- J
  johndavisSep 8, 2025
  To prevent crumbler roller clogging on your KUHN Farm Equipment, it is possible that there are wet conditions with too high load on the roller. Remove Crumbler roller removable bars and use Packer PK2 roller or Maxipacker roller.
C
Charles RomeroSep 12, 2025
What causes excessive wear on blades and blade holders of my KUHN HR3504D Farm Equipment?
- M
  matthew31Sep 12, 2025
  Excessive wear on blades and blade holders in your KUHN Farm Equipment can be due to a PTO speed that is too high, so reduce the PTO speed. It can also be caused by a levelling bar mounted at the rear, so remove the rear levelling bar if it is not required by working conditions.