KYORITSU KEW 6305 User Manual (English)

Other manuals for KYORITSU KEW 6305

Instruction Manual138 pages

Quick Manual32 pages

Quick Start Guide4 pages

Questions and Answers:

J
Janice WalkerJul 31, 2025
Why are the readings not stable on my KYORITSU KEW 6305 Measuring Instruments?
- P
  Patty ParsonsJul 31, 2025
  Unstable or inaccurate readings can occur for several reasons. Ensure that voltage test leads and clamp sensors are properly connected. Verify that the instrument settings and the selected wiring configuration are appropriate, and that you are using the correct sensors with the correct settings. Check the voltage test leads for any breaks, and confirm that the input signal is not experiencing interference. Also, check for strong electromagnetic fields nearby and ensure the usage environment meets the instrument's specifications.
T
Teresa DixonAug 4, 2025
What to do if I get an error message when powering on my KYORITSU KEW 6305 Measuring Instruments?
- D
  david21Aug 4, 2025
  If you receive an error message upon powering on, first, power off the instrument and then power it on again. If the error message disappears, there is no problem. However, if the same error message reappears, it may indicate damage to the internal circuit. In this case, contact your local Kyoritsu distributor. Also, if the error message (Err.001) is only shown on the RTC item, it means the internal coin battery for backup is exhausted. Contact your local Kyoritsu distributor. Note that the backup battery life is approximately 5 years.
R
Ruth MooreAug 9, 2025
Why is my KYORITSU KEW 6305 Measuring Instruments not saving data to the CF card?
- J
  Joshua CampbellAug 9, 2025
  If data cannot be saved to the CF card, verify the following: * The CF card is correctly inserted. * The CF card has been formatted. * There is available space on the CF card. * The destination for saving data is set to “CF card”. * You are not exceeding the maximum number of files or the capacity of the CF card. * The CF card operation to be used is checked. * The CF card operates properly on other hardware.
B
bruce22Aug 13, 2025
How to fix download and setting issues via USB communication with KYORITSU Measuring Instruments?
- K
  Katelyn MooreAug 13, 2025
  If you're experiencing issues with download and settings via USB, first confirm that the instrument and PC are connected with the USB cord correctly, the SET UP Range is selected, and the device is recognized on KEW PQA MASTER. If no device is recognized, a USB driver may not be installed correctly.
H
Hannah SmithAug 17, 2025
What to do if my KYORITSU KEW 6305 Measuring Instruments won't power on?
- J
  Johnathan JacksonAug 17, 2025
  When operating with an AC power supply, check: * The power cord is connected firmly and properly. * There is no break in the power cord. * The supply voltage is within the allowable range. When operating with batteries, check: * Batteries are installed with observing correct polarity. * Ni-HM batteries are full-charged. * Alkaline batteries are not exhausted.
C
Christopher Scott DDSAug 21, 2025
Why can't I save data to the internal memory of my KYORITSU Measuring Instruments?
- K
  Kurt HallAug 21, 2025
  If you are unable to save data to the internal memory, check the number of files currently stored in the memory and ensure that the destination for saving data is set to internal memory.
A
Andrew OsborneAug 26, 2025
What to do if any key doesn’t work on KYORITSU KEW 6305 Measuring Instruments?
- J
  Jessica JohnsonAug 26, 2025
  If a key doesn't work, verify that the key lock function is inactivated. Also, check the effective Keys on each Range.

KYORITSU KEW 6305 Specifications

General

Test Voltage	50V, 100V, 250V, 500V, 1000V
Phase Rotation	Yes
Earth Resistance	0.01 Ω to 2000 Ω
PSC/PFC	Yes
Diode Test	Yes
Applicable Standards	IEC 61010-1
Insulation Resistance Measurement Range	0.01MΩ to 2000MΩ
AC Voltage	0.1V to 600V
Frequency	45Hz to 65Hz
Loop Impedance	2000 Ω
RCD Test	30 mA, 100 mA, 300 mA, 500 mA
Trip Current	10mA - 1000mA (Ramp Test)
Resistance Range	0.01 Ω
Display	LCD
DC Voltage	0 to 600 V