Need help?Do you have a question about the Lamtec LT3-F and is the answer not in the manual?
General| Brand | Lamtec |
|---|---|
| Model | LT3-F |
| Category | Transmitter |
| Language | English |
Details the manual's applicability to software version 1.0.0.0 and required components.
Explains how to use the manual, highlighting warnings, pictograms, and intended user profile.
Defines safety symbols (Danger, Warning, Caution, Notice) and operator responsibilities.
Describes the intended operation, prerequisites, and conditions for safe use of the LT3-F.
Identifies qualified personnel and user groups with access levels for operating the device.
Outlines hazards from electrical equipment and protective measures against gas leakage.
Explains the LT3-F's use for simultaneous O2 and CO/H2 measurement in combustion systems.
Presents the EU Declaration of Conformity for the LT3F Lambda Transmitter and KS1D probes.
Illustrates standard and HT designs of the KS1D probe and its components.
Describes options for extending the probe's connection cable and maximum distances.
Explains basic navigation using arrow keys, ENTER, and BACK keys within the device menus.
Overview of the device's menu hierarchy, including sections for password, information, calibration, and settings.
Explains the meaning of symbols and indicators in the device's status line.
Details the main display and options available in the main menu.
Guides users on accessing the password entry screen within the main menu.
Guides users on accessing the information screen within the main menu.
Guides users on accessing the calibration screen within the main menu.
Guides users on accessing the settings screen within the main menu.
Specifies prerequisites and software version checks for correct operation of the system.
Provides safety warnings and guidelines for installing the probe and system components.
Outlines steps for initiating measurement after installation, including calibration.
Guides users on entering passwords to access different operational levels.
Explains how to activate/deactivate maintenance mode for calibration and testing.
Details the internal resistance regulation and its optimal operating point.
Describes how to prematurely end the cold start sequence and its implications.
Guides users on how to view O2, COe, and internal resistance values on the device.
Explains the importance and methods of probe calibration (reference measurement, test gas).
Details the procedure for O2 offset calibration, adapting measured values to ambient conditions.
Explains O2 electrode calibration using reference measurement or test gas.
Details calibration of the CO/H2 electrode using reference measurement or test gas.
Allows various parameter adjustments based on user access level, covering maintenance, filter time, outputs etc.
Provides details of the probe's test certificate and comparison with test bench values.
Explains the probe certificate, its completion, and importance for warranty and repairs.
Details periodic checks and calibration procedures for the KS1D probe.
Explains how to calibrate the probe using test gases, including safety warnings.
Explains calibration using a reference measurement.
Details a basic function test for the CO/H2 electrode with safety warnings.
Identifies parts subject to wear and suggests replacement intervals.
Guides on diagnosing probe issues and initiating the replacement process.
Provides detailed steps for replacing the sensor in the KS1D-HT probe.
Explains how faults and warnings are indicated and how to reset them.
Lists specific fault codes and their explanations, including help procedures.
Lists warning codes and their explanations, including help procedures.
Guides on accessing and viewing the recorded fault history.
Provides guidance on safe decommissioning procedures, including precautions for gas emissions.
Details the functional description and setup of analogue output modules (address 19).
Explains factory default settings for analogue output configuration.
Guides on adjusting analogue output ranges through the user interface.
Covers the functional description and setup of digital output modules (addresses 03 and 51).
Explains factory default settings for digital output configurations.
Describes how to diagnose the status of digital outputs using LEDs.
Details the functional description and setup of digital input modules (addresses 11 and 55).
Explains factory default settings for digital input configurations.
Describes how to diagnose the status of digital inputs using LEDs.
Explains the functional description and calculation method for combustion efficiency.
Provides guidance on connecting LSB modules externally and their power supply.
Guides on checking module connections, setting addresses, and interpreting LED status.
Specifies conditions for safe storage and transport of the device.
Advises on ecological design and proper disposal of electronic components.
Lists spare parts for the LT3-F motherboard, modules, and user interface.
Details spare parts for the KS1D combination probe when it is in housing.
Lists spare parts for the KS1D combination probe without housing.
Lists spare parts specific to the KS1D-HT high-temperature combination probe.
Explains deviations in O2 measurements between wet and dry flue gas conditions.
To Next Page
