EasyManua.ls Logo

LAUNCH TECH TWC-502RMB - User Manual

LAUNCH TECH TWC-502RMB
23 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LAUNCH Tyre Changer(TWC-502RMB)
i
Trademark Information
is a registered trademark of LAUNCH
TECH. CO., LTD. (LAUNCH for short) in China and
other countries. All other LAUNCH trademarks,
service marks, domain names, logos, and company
names referred to in this manual are either
trademarks, registered trademarks, service marks,
domain names, logos, company names of or are
otherwise the property of LAUNCH or its affiliates. In
countries where any of the LAUNCH trademarks,
service marks, domain names, logos and company
names are not registered, LAUNCH claims other
rights associated with unregistered trademarks,
service marks, domain names, logos, and company
names. Other products or company names referred to
in this manual may be trademarks of their respective
owners. You may not use any trademark, service
mark, domain name, logo, or company name of
LAUNCH or any third party without permission from
the owner of the applicable trademark, service mark,
domain name, logo, or company name. You may
contact LAUNCH by visiting Launch at
http://www.cnlaunch.com, or writing to LAUNCH,
Launch industrial Park, North WuHe Avenue,
Banxuegang industrial Park, Longgang District,
ShenZhen,Guangdong Province, P.R.China. to
request written permission to use Materials on this
manual for purposes or for all other questions relating
to this manual.
Copyright Information
Copyright © 2000 by LAUNCH TECH. CO., LTD. All
rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise,
without the prior written permission of LAUNCH. The
information contained herein is designed only for the
use of this unit. LAUNCH is not responsible for any
use of this information as applied to other units.
Neither LAUNCH nor its affiliates shall be liable to the
purchaser of this unit or third parties for damages,
losses, costs, or expenses incurred by purchaser or
third parties as a result of: accident, misuse, or abuse
of this unit, or unauthorized modifications, repairs, or
alterations to this unit, or failure to strictly comply with
LAUNCH operating and maintenance instructions.
LAUNCH shall not be liable for any damages or
problems arising from the use of any options or any
consumable products other than those designated as
Original LAUNCH Products or LAUNCH Approved
Products by LAUNCH.
General Notice
Other product names used herein are for
identification purposes only and may be
trademarks of their respective owners.
LAUNCH disclaims any and all rights in
those marks.

Questions and Answers

  • E
    Elizabeth MclaughlinAug 16, 2025
    Why doesn't the motor turn or have enough torque on my LAUNCH TECH Tyre Changers?
    • C
      Christian HartmanAug 16, 2025
      If the motor of your LAUNCH TECH Tyre Changer doesn't turn or the output torque is insufficient, it could be due to several reasons. First, check if any moving parts are stuck and remove any obstructions. If that's not the issue, the capacitor might be faulty and need replacement. Low voltage can also cause this problem, so pause and wait for the voltage to stabilize. Finally, inspect the circuit for any open connections and repair them if necessary.
  • T
    tatelisaAug 19, 2025
    Why is the tilting post on my LAUNCH TECH Tyre Changers tilting too fast or too slow?
    • R
      Ryan WashingtonAug 19, 2025
      If the tilting post on your LAUNCH TECH Tyre Changer is tilting too fast or too slow, it could be due to the pushing cylinder expelling too much or too little air, or because the pressure of compressed air has not reached 8 bar. To resolve this, open the side cover of the cabinet and slightly adjust the two air inflation regulators by hand to smooth the movement, then tighten the cap.
  • R
    Rebecca LunaAug 22, 2025
    What to do if I found air leakage in LAUNCH TECH Tyre Changers?
    • M
      mlopezAug 22, 2025
      If you find air leakage in your LAUNCH TECH Tyre Changer, it could be due to a damaged air hose, a damaged outlet of the air valve, or missing gasket cement. Replace the related part if the air hose or outlet of the air valve is damaged. If the gasket cement is gone, add gasket cement.
  • L
    Linda WatsonAug 25, 2025
    Why doesn’t the turntable turn on my LAUNCH TECH Tyre Changers?
    • H
      Heather PinedaAug 26, 2025
      If the turntable of your LAUNCH TECH Tyre Changer isn't turning, several issues could be the cause. The belt might be damaged or loose, in which case you should replace or tension it, respectively. Alternatively, the power switch could be damaged and require replacement. Another possibility is a problem with the motor; check the power wire and replace the motor if necessary.
  • R
    Regina MendozaAug 27, 2025
    What causes weak cylinder output in LAUNCH TECH Tyre Changers?
    • G
      Gary AndersonAug 27, 2025
      If the cylinder on your LAUNCH TECH Tyre Changer is weak in output, it could be due to air leakage, which requires strengthening the seal. Alternatively, mechanical hindrance could be causing the problem, which needs to be fixed. Another possibility is that the pressure of the compressed air is not high enough, in which case you should change the air source.
  • K
    Kevin LewisAug 30, 2025
    How to fix abnormal noise at the moving part of LAUNCH TECH Tyre Changers?
    • M
      Madison McknightAug 30, 2025
      If there is abnormal noise at the moving part of your LAUNCH TECH Tyre Changer, it may be due to a loose fixing screw, which needs to be tightened. Alternatively, there could be foreign matter inside, which needs to be removed.
  • V
    Vincent ClarkSep 2, 2025
    Why can the turntable on my LAUNCH TECH Tyre Changers only turn in one direction?
    • C
      clunaSep 2, 2025
      If the turntable on your LAUNCH TECH Tyre Changer can only turn in one direction, the power switch may be damaged. Replace the power switch to resolve this issue.
  • R
    Rebecca HarveySep 4, 2025
    What to do if the pedal on my LAUNCH TECH Tyre Changers can not be restored to its original position?
    • K
      Kristin SmithSep 4, 2025
      If the pedal of your LAUNCH TECH Tyre Changer cannot be restored to its original position, the return spring is likely damaged. Replace the return spring to fix this issue.
  • J
    Joshua GreenSep 7, 2025
    Why is the lock valve clogged after pressing the lever on my LAUNCH TECH Tyre Changers?
    • W
      Wayne LozanoSep 7, 2025
      If the lock valve on your LAUNCH TECH Tyre Changer is clogged after the lever is pressed, it could be due to a damaged O-ring on the valve, in which case you should replace the valve or O-ring. Alternatively, there may be a problem with the airflow regulating valve; adjust or replace the pressure regulating valve and replace the airflow regulating valve.
  • B
    Bruce MartinezSep 10, 2025
    What causes the turntable to not lock the rim tightly on LAUNCH TECH Tyre Changers?
    • J
      Jeffrey SullivanSep 10, 2025
      If the turntable on your LAUNCH TECH Tyre Changer cannot lock the rim tightly, it could be due to worn jaws, which should be replaced. Another possible cause is air leakage in the clamping cylinder, in which case you should replace the cylinder seal.

Summary

Safety Precautions

Precautions

Operate by trained personnel, install on stable ground, maintain ventilation, avoid extreme conditions, avoid dust, keep others away, use safety equipment, pay attention to marks, avoid moving parts, don't remove safety devices, use specified lubricants, contact maintenance before moving.

Description of Safety Signs

The Position of Safety Signs

General Information

Main Structure

Operation

Demounting Tyre

Steps for deflating, cleaning the rim, lubricating the bead, and separating the tyre from the rim.

Mounting Tyre

Mounting Tyre

Steps to mount the tyre bead onto the rim, ensuring proper positioning and bead crossing.

Inflating Tyre

Danger!

Describes crucial safety warnings for the inflation process.

Safety Procedures

Trouble Shooting

Maintenance

Maintenance

Keep machine clean, clean hexagonal column, clean and lubricate arms, clean turntable/jaws, lubricate base pin, lubricate rubbing surfaces, check oil level, drain condensed material, adjust belt tension, check bolts.

TWC-502 RMB Oil Safety Data

TWC-502 RMB Circuit Diagram

TWC-502 RMB Pneumatic Diagram

LAUNCH TECH TWC-502RMB Specifications

General IconGeneral
BrandLAUNCH TECH
ModelTWC-502RMB
CategoryTyre Changers
LanguageEnglish