LEE PRECISION, INC. 4275 HWY. U HARTFORD WISCONSIN 53027
www.leeprecision.com
Setup Tools required:
• Safety glasses & ear protection
• ” wrench or socket
• Qty. 2, ⁄” wrench
• # 1 Phillips screwdriver
• ⁄” Hex Wrench
PRO 1000 3 STATION RELOADING PRESS
COMPLETE INSTRUCTIONS
Helpful setup &
operation videos
available on
leeprecision.com
OPTIONAL ACCESSORY:
CASE COLLATOR
# 90667
Auto-Drum
Powder
Measure
CASE FEEDER TUBES
(7-PACK) # 90661
TURRET # 90497
ACTION ROD # TR2438
FOLDING PRIMER TRAY
(1 included)
(2-PACK) # 90606
TURRET RING #
TP2126
FEED PLATE
CASE FEED SPRING #
PR2118
RAM PIN # OF3221
PRIMER DISPOSAL TUBE # BP3064
CAP # BP3127
1
” WASHER
#
OF3609
–18 X 1
BOLT
#
FO2113
LEVER CLAMP # OF3613
30 & 32 cal. Bullets up to .60 long # 90892
9mm through .365 diameter up to .46 long # 90893
9mm through .365 diameter .46 to .60 long # 90894
9mm through .365 diameter .60 to .75 long # 90895
40 cal. through .44 cal. up to .65 long # 90896
40 cal through .44 cal .65 to .80 long # 90897
45 cal. bullets .50 to .67 long # 90898
LEE BULLET FEEDER OPTIONAL
Automatically feeds bullets into the mouth of the seating
die. Aligns bullets more accurately than possible by
hand. Increases cyclic rate to
CASE SLIDER BLOCK
CONNECTING LINK #
TP2129
BASE CASTING # TR3642
PRIMER OUTLET & RETAINING RING #TP3707
LINK BOLT (2) #
TP2117
LINK NUT (2) # FB1181
TOGGLE ( 2 ) # OF2853
5-/6-18 x 1 1/4 BOLT
Qty. 3 #FT2886
PRIMER
ATTACHMENT
# 90660
SHELL PLATE CARRIER
# TR3975
Lubricate these points often:
· Ammunition reloading can be dangerous if done im properly and can result in serious injury or death.
· Reloading rifle ammunition requires extra care due to extremely high pressures. Make sure your cases are in good condition. Inspect them before
each reloading for damage and wear. Cases must be trimmed. An excessively long case will pinch the bullet in the end of the rifle chamber and cause
dangerously high pressure that could damage your gun and cause personal injury.
· Use only Remington™ or CCI™ primers. Other brands like Federal™, can explode with sucient force to seriously injure the user or persons nearby.
Never place more than 100 primers in the tray.
· Reloading should not be attempted by persons not willing and able to read and fol low instructions exactly. Do not permit distractions while loading.
This is a complex machine that needs your fullest attention.
· Children should not be permitted to reload ammunition without strict parental supervision.
· Always wear safety glasses and hearing protection when reloading and shooting.
· Ammunition loaded with these tools and data should only be used in modern guns in good condition. We do not accept responsibility for ammunition
loaded with these tools or data as we have no control over the manufacture and storage of components or the loading procedure and techniques.
Primers and gun powder, like gasoline and matches, can be dangerous if improperly handled or misused.
· Verify proper powder and charge for bullet weight selected.
· Be extremely careful to avoid a double charge. If in doubt, empty the case and recycle it.
DANGER
CAUTION
WARNING: Handling live
primers and spent primers
may expose you to lead or
other chemicals, which are known
to the State of California to cause
reproductive harm and cancer. For
more information, go to
www.P65Warnings.ca.gov.
WARNING: This product
may contain steel alloyed
with trace amounts of
lead and other elements which are
known to the State of California
to cause reproductive harm and
cancer. For more information, go
towww.P65Warnings.ca.gov. To
prevent exposure, do not alter the
product by welding, grinding, etc.
OPTIONAL ACCESSORY:
BIN & BRACKET for
catching completed rounds
# 90687
RISER BLOCK
OPTIONAL ACCESSORY:
RELOADING STAND
# 90688
Rust proof these points often:
Ram
Link bolt
Link bolt
Ram pin
STP
motor oil
treatment
works well
Dry Coat
rust
preventative
works well
Turret ring
Handle & lever clamp
(3)
Columns
To Next Page
Need help?
General
