8100_A Technical description
59
Code 1eve 1 Factory
I
customer
settings settings
.C018 Chopper frequency
fch
.C019 Threshold of
automatic
DCbrake
C025Preselection:
Encoder
Parameter levelPRG
<===>
-------------------....----------------------------------
-0- SH+ PRG
1000 Hz
-2-
C026 Constant for [C02S1
1 1_________.___________
---------------------------------------------------------
-1- SH + PRG 1500 Hz
(lmV) I term.I,2
OmV
term 8
Omv
xs: -1-
C027 Setting for [C02S1
1 1_________.___________
Lenze
------------------------------------------------------.--
-2- SH + PRG
2000 Hz
- --- -- -- - --- -- --- ---- -- - - -- - -- - --- --- -.-- --- --- ~~~~~-- ---
-3- SH + PRG 3300 Hz
~- - - - - - - - - - - - - - - - ~- - ~- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - --
-4- SH+ PRG
3600 Hz
. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ~ - - - - - - -. - --
-5- SH + PRG
4000 Hz
--- -------- ~--~---- .-- ---- --~--~---- ---- ---~ --- --
Change is only possible when controller inhibitedl
xxx Hz 0.. .480Hz 0.0.. .100Hz (O,IHz) I O.OHz
100.. .480Hz (1Hz)
Withthe setting 0.0 Hz the automaticactivation
of the DCbrake is switched off.
First, select the input to be adjusted via C02S.
Then, adjust the inputs us;ng C026 and C027.
~ - - - - - - - - - - - - - - - - - - - - - - - - -. - - - - - - - - - - - - - - - - - - - - - - - - - - - - --
-1- SH + PRG Analog input term. I, 2 I -4-
Set-value 2 when COOS=-1- ... - 16-
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ~- - -. - -. - - - - - - ~- - - - - - --
-4- SH+ PRG Actual value input term. 3, 4
Actual value wit e005 = -11-
---------------------------------------------------------
-10- SH + PRG Pulse train/lncremental encoder input X5
(Tracks A, A/, B, BI)
Set-value 1 with COOS=-2-
Actual value with COOS=-13-,-16-
---------------------------------------------------------
-11- SH+ PRG Pulse train input XS
(Tracks 0, 01)
Set-value 1 with COOS=-16-
For analog inputs
---------------------------------------------------------
xxxx -1000 ... +100OmVOffset correct;on
For input of pulse train/
incremental encoder X5
------------------------------------------------.--------
-1- SH + PRG
512 pulses/Hz or increments/rev.
---------------.--------------------------------.--------
-2- SH + PRG 1024 pulses/Hz or increments/rev.
---------------------------------------------------------
-3- SH + PRG 2048 pulses/Hz or increments/rev.
---------------------------------------------------------
-4- SH + PRG 4096 pulses/Hz or increments/rev.
For analog inputs
. - - - - - - - - - - - - - -.. - - - - - - - - - - - - - - - - -. - - - - - - - - - - - - - - ~- - - - - --
For input of pulse train/
incremental encoder X5
{o.oon I term.I,2
1.000
term 8
1.000
XXXX -2.500 ... +2.500 Signal """lification
---.----------------.--------------.--.-.----------------
{o.oon IxS: 1.000
XXXX -5,000 ... +5,000 Signal """I if;cat;on
-----......-------------..--.--------------.---.---------
For set-value input via pulse train:
The field frequency is obtained from
fdsoll [HzI = fLeit [HzI . C0271C026.
----------.---.-.-.-.-----------.------------------.--.-.
For actusl value feedback via incremental encoder:
With e026, the ",.ITDerof increments for one
revolution of the shaft can be entered.
To Next Page
Loading...
