Lenze 8603 E.6x.6 Series

To Next Page

To Previous Page

116



Main Page

Table of Contents5
General Data10
Dimensions11
Scope of Supply11
Application as Directed12
CE Conformity13
- Directive (73/23/EEC)14
EC Declaration of Conformity ´95 for the Purpose of the EC Directive Relating to Electromagnetic Compatibility (89/336/EEC)15
Manufacturer's Declaration for the Purpose of the EC Directive Relating to Machinery (89/392/EEC)17
Applications with Extreme Overload, Peak Torque up to 230% of the Rated Motor Torque18
Applications with High Overload, Peak Torque up to 170% of the Rated Motor Torque19
- Application with Medium Overload, Peak Torque up to 135% of the Rated Motor Torque20
Mechanical Installation21
Electrical Installation22
Motor Protection23
Installation in Compliance with EMC23
CE-Typical Drive Systems24
Switching on the Motor Side26
Power Connections28
Tightening Torques of the Power Terminals29
Control Connections29
Analog Inputs and Outputs30
Further Inputs and Outputs30
Description of the Analog Inputs and Outputs31
Description of Other Inputs and Outputs31
Digital Inputs and Outputs32
Description of the Digital Inputs and Outputs34
Frequency Output 6⋅ Fd35
Operation with DC Bus Supply36
Connection of Several Drives for Energy-Sharing36
DC Voltage Supply36
Screenings37
Grounding of Control Electronics37
Brake Resistors38
Selection of the Brake Resistor39
Technical Data of Brake Resistors41
Mains Chokes42
Selection of the Mains Choke43
Technical Data of Mains Chokes44
Motor Filter45
Technical Data of Motor Filter46
Motor Voltage Filter47
Technical Data of Motor Supply Filters48
Cable Protection49
RFI Filters50
Ratings of RFI Filters50
Technical Data of RFI Filters51
Accessories for Digital Frequency Networking51
Connecting Module 2110IB− Interbus-S52
Connecting Module 2130IB− PROFIBUS52
Connecting Elements for Optical Fibre Cables−Lecom-LI53
Level Converter 2101IP− LECOM-A/B53
Adapter RS485 (LECOM Interface X6)53
Key Functions55
Plain Text Display55
Changing Parameters56
Parameter Setting by Two Codes58
Save Parameters58
Load Parameters58
Operating Mode59
Controller Enable60
Quick Stop / Select Direction of Rotation60
Configuration62
Example of How to Select a Configuration63
Signal Flow Chart64
Features of Set-Value66
Set-Value Input with Master Current66
Digital Frequency Input67
Features of Set-Value68
Offset and Gain Adjustment68
Control Mode69
V/F Characteristic Control70
I0 Control72
Minimum Field Frequency Fdmin73
Maximum Field Frequency Fdmax73
Acceleration and Deceleration Times Tir, Tif74
Analog Feedback75
Digital Feedback75
Frequency Pilot Control76
Adjustment of the Feedback Gain77
Automatic Adjustment77
Manual Adjustment78
Setting of the Controller Parameters78
Additional Functions79
Freely Assignable Digital Inputs80
Functions of the Freely Assignable Digital Inputs81
Set TRIP81
Reset TRIP81
DC Injection Braking81
JOG Frequencies82
Additional Acceleration and Deceleration Times84
Ramp Generator Stop86
Ramp Generator Input86
Integral Action Component86
Process Control86
Select Parameter Set, Load Parameter Set87
Freely Assignable Digital Outputs, Relay Output88
Functions of the Freely Assignable Digital Outputs89
Frequency below a Certain Level , Qmin89
Maximum Current Reached, Imax89
Set-Value Reached89
Fault Indication TRIP90
Ready, RDY90
Pulse Inhibit, IMP90
Feedback = Set-Value90
Feedback90
Flying Restart Circuit Active91
Process Control Active, Process Step Active91
Monitor Outputs91
Digital Frequency Output X9 (Option)92
Chopping Frequency93
Automatic Chopping Frequency Reduction94
Automatic DC Injection Braking94
Slip Compensation94
S-Shaped Ramp Generator Characteristic95
Limitation of the Frequency Setting Range95
Process Control96
Flying Restart Circuit97
Oscillation Damping98
Load Change Damping98
Overload Protection of the Frequency Inverter (I⋅T Monitoring)99
Overload Protection of the Motor99
PTC Input99
I²⋅T Monitoring100
Code Set101
Language101
Display of the Actual Values102
Switch-On Display102
Identification102
LECOM1 Interface X6111
LECOM2 Interface (Option)112
LECOM Codes112
Controller Address112
Operating State112
Controller State112
Pole Pair Number112
Baud Rate (LECOM1)113
History of Reset Faults113
Code Bank (LECOM1)113
Enable Automation Interface (LECOM2)113
High Resolution Data114
Attribute Table115
Checking the Mains Rectifier122
Checking the Power Stage122
Checking the Voltage Supply on the Control Board 8602MP122

Lenze 8603 E.6x.6 Series - Page 118

Table of Contents

Related product manuals