What to do if Lenze Control Unit SMV drive stops and “F.nF2” fault is displayed; P419 code is “1xxx”?
If the SMV drive stops and displays the “F.nF2” fault with a P419 code of “1xxx”, it indicates that the Master device forced a Network fault using the Control Supervisor Object 0x29-1-17 “Force Fault Trip”. Check the Master device control logic to resolve this.
Why Lenze SMVector Decel Override?
If the Lenze Inverter has stopped decelerating to avoid tripping into fault due to excessive motor regen (2 sec max), and it trips into fault, increase P105 and P126. Alternatively, install a Dynamic Braking option.
How to fix Lenze SMVector Inverter Dynamic Braking fault?
If the Lenze Inverter dynamic braking resistors are overheating, increase the active deceleration time (P105, P126, P127) and check the mains voltage and P107.
What to do if Lenze SMVector Inverter OEM Defaults data fault?
If the Lenze Inverter drive is powered up with P199 = 1 and the OEM settings in the EPM are not valid, install an EPM containing valid OEM Defaults data or change P199 to 0.
What does it mean if the Lenze Control Unit SMV drive cannot be accessed from the network and the P419 Code is "083"?
If the SMV drive cannot be accessed from the network and the P419 Code is "083", it indicates a duplicate DeviceNet address. Ensure the SMV drive address is unique, reset the SMV drive by cycling power, and use the Faulted Node Recovery utility to resolve this.
Why does the Lenze Control Unit SMV drive stop without a fault when P419 code is “1111”?
If the SMV drive stops without a fault and the P419 code is “1111”, it means the master device closed the established connection when the SMV drive was in Network Control Mode, and the Parameter P419 DeviceNet Idle Mode is set to 0 (“Stop the Drive”). To resolve this, switch off Network Control before the established connection is closed, set the DeviceNet Parameter P419 DeviceNet Idle Mode to 1 (“Hold Last State”), and re-establish the connection and restart the SMV drive.
How to fix no communications from the option module in Lenze Control Unit?
If there are no communications from the option module in your Lenze Control Unit, there could be several reasons: * The module might not be initialized: Check the drive to module connection and verify parameters P400 and P402. * Incorrect EtherNet/IP settings: Check parameters P410 - P421. If unsure, reset EtherNet/IP parameters to factory default using P403. Power cycle the drive after changing the IP address setting or use P408. * Improper wiring: Check the wiring between the EtherNet/IP network and communication module. Ensure that the terminal block is properly seated and check the connection between the module and the drive.
How to fix Lenze Control Unit module to drive communication timeout?
If the module to drive communication is timing out, the connection between the drive and the module might not be properly established. Check the cable and connection between the module and the drive to resolve this issue.
How to resolve Lenze SMVector Inverter EPM fault?
If the Lenze Inverter displays an EPM fault because the EPM is missing or defective, power down the drive and replace the EPM.
Why Lenze SMVector OEM Settings Operation warning?
If the Lenze Inverter shows an OEM Settings Operation warning because an attempt was made to change parameter settings while the drive is operating in OEM Settings mode, note that in OEM Settings mode (P199 = 1), making changes to parameters is not permitted.
Covers handling, operation, installation risks, and qualified personnel requirements.
Guidelines for safe installation, avoiding mechanical stress and environmental hazards.
Observing national regulations for electrical installation and EMC compliance.
Using the drive as a safety device, emergency stops, and automatic restart.
Policy on warranty and liability for explosion proof motor applications.
Systems require additional monitoring and protection devices for safe operation.
Understanding icons, signal words (DANGER, WARNING, STOP, NOTE), and their consequences.
Limits for harmonic current emissions and required compliance measures.
Electrical shock hazard from charged capacitors and PE conductor current.
UL warnings for circuit capability, wire type, pollution degree, and plenum rating.
Conformity, approvals, voltage imbalance, humidity, temperature, and enclosure ratings.
Explains the structure of the SMVector inverter model number.
Specifications for 120V/240VAC, 240V single/three phase, 400-480VAC, and 600VAC models.
Physical dimensions and mounting screw details for NEMA 1 (IP31) models.
Detailed dimensions and conduit hole specifications for NEMA 1 models.
Dimensions and mounting details for larger NEMA 1 models.
Physical dimensions and conduit hole specifications for NEMA 4X models.
Dimensions and conduit hole details for NEMA 4X models with a disconnect switch.
Covers storage, power connections, motor connections, and wiring diagrams.
Recommendations for fuses, circuit breakers, and power wiring for various SMV models.
Descriptions of control terminal strips and their functions for different HP ranges.
Explains keypad buttons (START, STOP, ROTATION, MODE) and display indicators.
Configuring start/reference control sources and drive operating modes.
Overview of parameter setting, using the EPM, and basic setup parameters.
Configuring digital inputs, outputs, and their functions.
Setting advanced parameters, PID control, and analog input configurations.
Configuring vector modes, motor data, and network communication settings.
Monitoring diagnostics, faults, and configuring sequencer operation.
Illustrates the logic for starting segments based on digital inputs and P100/P700 settings.
Shows sequence actions, repeat cycles, suspend logic, and end segment control.
Displays the active segment, output voltage, and segment delay status.
Lists drive status/warning codes, their causes, and remedies.
Explains the 4-digit codes indicating drive configuration and stop sources.
Lists common fault codes (F_AF, F_AL, F_CF etc.) with their causes and remedies.
Details on faults like F_dbF, F_EF, F_FI, F_FOL, F_HF, F_IL, F_n Id.
Covers faults F_OF, F_OF I, F_PF, F_rF, F_SF, F_UF, F_FAU.
Table showing maximum permissible cable lengths for SMV models with internal EMC filters.
General| Protection Class | IP20 |
|---|---|
| Overload Capacity | 150% for 60 seconds |
| Communication Options | CANopen, Profibus DP |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short Circuit |
| Control Method | Sensorless Vector |
| Ambient Temperature | -10°C to +40°C |
To Next Page
