Lenze EVS9323-ES

Appendix
11-32

BA9300SU EN 2.1
Code ImportantPossible settingsLCDCode Important
ChoiceLenze
LCD
C0472
1
2
3
...
19
20
)&2'( D1DMOH
)&2'( D1DMOH
)&2'( D1DMOH

)&2'( D1DMOH
)&2'( D1DMOH
0.00
0.00
100.00
...
0.00
0.00
-199.99 {0.01 %} 199.99 Used for relative analog signals
C0473
1
2
3
...
9
10
)&2'( D%R
)&2'( D%R
)&2'( D%R

)&2'( D%R
)&2'( D%R
1
1
0
...
0
0
-32767 {1} 32767 Used for absolute analog signals
C0474
1
..
5
)&2'( 3+

)&2'( 3+
0 -2147483648 {1} 2147483648 FCODE phase
Freely assignable code for phase signals
1 turn = 65536 inc
C0475
1
2
)&2'( ')
)&2'( ')
0 -16000 {1 rpm} 16000 FCODE phase difference
Used for phase difference signals
1 turn = 65536 inc
[C0490]
)FF'%DEL POR
0 0{1} 4
0ResolveratX7
1 Encoder TTL at X8
2 Encoder sin at X8
3 Absolute ST at X8
4 Absolute MT at X8
Position feedback system
• C0490 = 0, 1, 2 can be mixed with C0495
=0,1,2
• C0490 = 3, 4 sets C0495 to the same value
[C0495]
)FF'%DEL 1
0 0{1} 4
0ResolveratX7
1 Encoder TTL at X8
2 Encoder sin at X8
3 Absolute ST at X8
4 Absolute MT at X8
Speed feedback system
• C0495 = 0, 1, 2 can be mixed with C0490
=0,1,2
• C0495 = 3, 4 also sets C0490 to the same
value
C0497
1DESGJMSF5
2.0 0.0 {0.1 ms} 50.0
0 ms switched off
Nact-filter time constant
Time constant for actual speed
C0517
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
...
31
32
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18
8RF5 NF18

8RF5 NF18
8RF5 NF18
51.00
54.00
56.00
46.00
49.00
183.00
168.01
86.00
22.00
5.00
11.00
12.00
13.00
105.00
39.01
70.00
71.00
0
0
94.00
3.00
0.00 {0.01} 1999.00
C0051/0 MCTRL-NACT
C0054/0 Imot
C0056/0 MCTRL-MSET2
C0046/0 N
C0049/0 NADD
C0183/0 Diagnostics
C0168/1 Fail no. act
C0086/0 Mot type
C0022/0 Imax current
C0005/0 Signal cfg
C0011/0 Nmax
C0012/0 Tir
C0013/0 Tif
C0105/0 QSP Tif
C0039/1 JOG setpoint
C0070/0 Vp speed CTRL
C0071/0 Tn speed CTRL
not assigned
not assigned
C0094/0 Password
C0003/0 Par save
User menu with up to 32 entries
• Under the subcodes the numbers of the
desired codes are entered.
• The input is done in the format xxx.yy
– xxx: Code number
– yy: Subcode for code
• It is not checked whether the entered code
exists.
[C0520]
J1
1000 FIXEDPHI-0 → Selection list 4 Configuration input
[C0521]
TP'JT
1000 FIXED 0 % → Selection list 1 Configuration gain factor numerator
[C0522]
5DS'JT
1000 FIXED 0 % → Selection list 1 Configuration gear factor numerator
[C0523]
$S5JN
1000 FIXED 0 % → Selection list 1 Configuration phase trimming
[C0524]
1S5JN
1000 FIXED 0 % → Selection list 1 Speed trimming of DFSET