Lexmark XM3150 Compatibility Guide

Media specifications
Labels Width: 76.2–216 mm (3.0–8.5 in.)
Length: 127–355.6 mm (5–14 in.)
Weight:
Up to 199 g/m
2
(53 lb)
Thickness: Up to 0.25 mm (0.01 in.)
Smoothness: 100–400* Sheffield
* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.
Card stock Weight:
Up to 163 g/m
2
Index Bristol (90 lb)
Up to 163 g/m
2
Tag (100 lb)
Note: Always use the rear exit when printing on card stock. To minimize curl, use the rear exit when printing on labels.
Card stock and label guidelines
When printing on labels:
• Set the Paper Type to Labels from the printer driver, the Local Printer Setup Utility, or MarkVision.
• Do not load labels together with paper or transparencies in the same paper source.
• Do not use label sheets with a slick backing material.
• Do not print within 1 mm (0.040 in.) of the die‑cut.
• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial
sheets will also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge
warranties.
• Use labels that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or
releasing hazardous emissions.
• Use labels that can withstand pressure of 25 pounds per square inch (psi).
• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.
• Do not use labels that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least
1 mm (0.040 in.) from the edges. Adhesive material will contaminate the printer and could void the warranty.
• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver
edge, and a non‑oozing adhesive should be used.
• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.
• Portrait orientation is preferred, especially when printing bar codes.
• Do not use labels that have exposed adhesive.
• For the multipurpose feeder, load labels with the recommended print side faceup and the top edge going in first.
For the tray, load labels with the recommended print side facedown.
When printing on card stock:
• Set the Paper Type to Card Stock from the printer driver, the Local Printer Setup Utility, or MarkVision.
• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting
introduces semi‑liquid and volatile components into the printer.
• Do not use card stock that is creased. It may cause paper jams.
• We recommend the use of grain short card stock.
• Load card stock with the recommended print side faceup and the top edge going in first.
Printer specifications 90

Lexmark XM3150 Specifications

General

Duplex printing	Yes
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	6.5 s
Print speed (black, normal quality, A4/US Letter)	47 ppm
All-in-one functions	Copy, Fax, Print, Scan
Color all-in-one functions	Scan
Digital sender	No
Maximum duty cycle	150000 pages per month
Recommended duty cycle	2000 - 15000 pages per month
Copier resize	25 - 400 %
Maximum copy resolution	- DPI
Copy speed (black, normal quality, A4)	47 cpm
Scan speed (black)	48 ppm
Scan speed (color)	32 ppm
Duplex scan speed (black)	21 ppm
Duplex scan speed (color)	14 ppm
Optical scanning resolution	600 x 1200 DPI
Faxing	Mono faxing
Modem speed	33.6 Kbit/s
Total input capacity	650 sheets
Total output capacity	250 sheets
Maximum input capacity	2300 sheets
Multi-Purpose tray input capacity	100 sheets
Envelopes sizes	7 3/4, 9, 10, DL
Maximum print size	216 x 356 mm
Paper tray media types	Card stock, Envelopes, Labels, Plain paper, Transparencies
Non-ISO print media sizes	Executive (184 x 267mm), Folio (media size), Legal (media size), Letter (media size), Oficio (media size)
ISO A-series sizes (A0...A9)	A4, A5, A6
JIS B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Display	LCD
Control type	Touch
Product color	Grey, White
Display diagonal	7 \
Market positioning	Business
Direct printing	-
Standard interfaces	Ethernet, USB 2.0
Optional connectivity	Parallel, Serial (RS-422), Wireless LAN
Internal memory	1024 MB
Maximum internal memory	3072 MB
Sound pressure level (copying)	56 dB
Sound pressure level (printing)	55 dB
Power consumption (average operating)	- W
Operating altitude	0 - 2896 m
Operating temperature (T-T)	16 - 32 °C
Operating relative humidity (H-H)	8 - 80 %
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	479 mm
Width	499 mm
Height	561 mm
Weight	23600 g