What to do if LEYBOLD ECODRY Plus does not reach nominal speed 210 Hz?
If the LEYBOLD Water Pump does not reach the nominal speed of 210 Hz, it could be due to: * Inlet pressure exceeding 50 mbar. Close the pump inlet and check the rotational speed on the display. * Blocked outlet or unacceptably high back pressure in the outlet. Ensure the pump outlet is clear and that the outlet pressure does not exceed 1200 mbar.
Why LEYBOLD Water Pump does not start?
The LEYBOLD Water Pump might not start due to several reasons: 1. No mains voltage present. Check the mains power supply and ensure the mains switch on the pump is set to '1'. 2. Defective or incorrectly inserted mains cable. Verify the pump’s power supply. 3. Incorrect connection of the start-stop switch. If operating using the start-stop switch, ensure the supplied plug is connected to the X1 control interface with pins 8 and 9 bridged. 4. Start-stop button is not set to 'start'. If operating using the X1 control interface, set the start-stop switch to 'start'. 5. DC Under voltage or Controller Under voltage. Compare the voltage range on the pump’s nameplate with the available mains voltage and connect the pump to a power supply at the correct voltage.
What to do if LEYBOLD ECODRY Plus Water Pump end pressure will not be reached?
If the end pressure is not reached in your LEYBOLD Water Pump, consider the following: * The gas ballast valve might be open. Close the gas ballast valve, if possible. * There could be a leakage in the system. Check for any leaks. * The gas ballast valve could be defective. Check for leaks. * The outlet might be blocked, or there's unacceptably high back pressure in the outlet. Ensure the pump outlet is clear and that the outlet pressure does not exceed 1200 mbar. * The pump might not be running at the rated rotational speed of 210 Hz. Set the target speed to 210 Hz using the X104 RS-485 interface.
Why LEYBOLD ECODRY Plus switches off?
The LEYBOLD Water Pump may switch off due to: * Heatsink Overheat. Set the pump up at a suitable location with a lower ambient temperature. * Cooling air supply or discharge impeded. Ensure sufficient cooling air supply or discharge. * Gas temperature too high. Check the system.
What to do if LEYBOLD Water Pump does not start or switches off?
If your LEYBOLD Water Pump does not start or switches off, it could be due to: * Voltage too low for controlling the frequency converter. Disconnect the pump from the mains for at least 10 seconds and restart. * Charging circuit for DC bus is defective. Disconnect the pump from the mains for at least 10 seconds and restart. * DC bus voltage was too high, the rundown time is too short, or the input voltage is too high. Compare the voltage range on the pump’s nameplate with the available mains voltage and connect the pump to a power supply at the correct voltage.
General| Brand | LEYBOLD |
|---|---|
| Model | ECODRY Plus |
| Category | Water Pump |
| Language | English |
Details hazards related to mechanical aspects of the pump and safe handling.
Covers electrical safety precautions and requirements for the pump.
Warns about burn risks from hot pump components.
Discusses risks from materials used and substances pumped.
Lists items included with the pump upon delivery.
Provides detailed technical specifications and parameters of the pump.
Instructions for safely lifting and moving the pump during transportation.
Guidelines for proper storage conditions and duration to prevent damage.
Instructions on positioning the pump on a level surface for optimal cooling.
Defines the intended gases and conditions for safe and effective pump operation.
How to operate the pump using the physical controls.
Overview of available interfaces for pump control and monitoring.
Recommends precautionary service intervals and maintenance.
Procedures for sending equipment to Leybold Service and contamination declarations.
Explains how alarms and faults are indicated and how to reset them.
Guidelines for decontaminating and disposing of the pump and its parts.
Lists the certifications and testing standards the pump has met.
To Next Page