54
62. Brightness Scheduling (Command: s s)
Sets Brightness Scheduling.
Transmission
[s][s][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. f1 to f6 (data reading)
F1: Reads the 1st quick brightness control's data
F2: Reads the 2nd quick brightness control's data
F3: Reads the 3rd quick brightness control's data
F4: Reads the 4th quick brightness control's data
F5: Reads the 5th quick brightness control's data
F6: Reads the 6th quick brightness control's data
2. FF: Reads all stored lists
3. e1 to e6 (Deletes one index), e0 (Deletes all indexes)
E0: Deletes all quick brightness controls
E1: Deletes the 1st quick brightness control
E2: Deletes the 2nd quick brightness control
E3: Deletes the 3rd quick brightness control
E4: Deletes the 4th quick brightness control
E5: Deletes the 5th quick brightness control
E6: Deletes the 6th quick brightness control
4. 00-17: 00 - 23 hours
Data2 00-3B: 00 - 59 minutes
Data3 00-64: Backlight 0 - 100
* To read or delete a list of quick brightness controls you have set,
[Data2][Data3] must be set to FF.
* If you want to read a complete list of quick brightness controls you have
set through FF, do not enter any values in [Data2][Data3].
* If you want to read a complete list of quick brightness controls you have
set through FF, NG is acknowledged if there is no stored list.
Example 1: ss 01 f1 ff ff - Reads the 1st index data from the
quick brightness control.
Example 2: ss 01 ff – Reads all index data from the quick
brightness control.
Example 3: ss 01 e1 ff ff - Deletes the 1st index data from the
quick brightness control.
Example 4: ss 01 07 1E 46 - Adds a schedule whose time is
07:30 and whose backlight is 70.
Acknowledgment
[s][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
* This feature may not be available for all models.
63. Sync Mode (Command: t g)
Selects a Sync Mode settings.
Transmission
[f][g][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
Acknowledgment
[g][ ][Set ID][ ][OK/NG][Data][x]
* This feature may not be available for all models.
64. Time Sync (Command: s n, 16)
Sets the time to synchronize.
Transmission
[s][n][ ][Set ID][ ][1][6][ ][Data][Cr]
Data 00: Off
01: Sets to 00:00
02: Sets to 1:00 AM
…
18: Sets to 11:00 PM
19: Plays back immediately (once)
Acknowledgment
[n][ ][Set ID][ ][OK/NG][ ][1][6][ ][Data][x]
* This feature does not work if there is no Master monitor.
* The settings screen is displayed only on the Master monitor.
* This feature does not work if the current time is not set.
* This feature may not be available for all models.
65. Timer Power On Scheduling (Command: f b)
Sets the Timer Power On Scheduling function.
Transmission
[f][b][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
Acknowledgment
[b][ ][Set ID][ ][OK/NG][Data][x]
66. Timer Power Off Scheduling (Command: f c)
Sets the Timer Power Off Scheduling function.
Transmission
[f][c][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
Acknowledgment
[c][ ][Set ID][ ][OK/NG][Data][x]
To Next Page
Loading...
Need help?
General
