What to do if my LG Dishwasher shows a DRAIN ERROR?
If your LG Dishwasher displays a DRAIN ERROR, it could be due to several reasons. First, try cleaning the filter. If that doesn't work, check the drain hose for any kinks or blockages and remove them. If the problem persists, the drain pump/motor or its circuit might be faulty, requiring you to replace the drain pump/motor or repair the circuit.
How to fix a THERMAL ERROR on my LG Dishwasher?
If your LG Dishwasher is displaying a THERMAL ERROR, it could be due to a problem in the thermistor circuit, in which case you should repair it. It could also mean the thermistor itself is faulty and needs to be replaced. Lastly, the controller might be the source of the error, requiring you to repair or replace it.
What to do if my LG LD-1415M1 shows an INLET ERROR?
If your LG Dishwasher displays an INLET ERROR, make sure the water tap is fully opened. Also, inspect the inlet hose for any kinks and repair them if necessary. Another potential cause is a clogged filter in the inlet valve due to impure water. To resolve this, close the water tap, unscrew the inlet hose at the inlet valve side, and clean the filter. If these steps don't solve the problem, consider replacing or repairing the inlet valve. Also, check for any water remaining on the base, inspect for damages, and disconnect the inlet hose to the dishwasher to unlock the safety valve.
What to do if my LG LD-1415M1 Dishwasher displays a LEAKAGE ERROR?
If your LG Dishwasher is showing a LEAKAGE ERROR, start by checking all hose connections for water leakage and replace the hose connections if needed. Inspect for any damages that may be causing the leak and repair or replace the damaged parts. Also, a worn-out impeller in the washing pump can cause leakage, so consider replacing the washing pump. Finally, check the applied voltage.
What does it mean when my LG Dishwasher shows a HEATER ERROR?
If your LG Dishwasher displays a HEATER ERROR, it could indicate a problem with the heater circuit, requiring you to repair the circuit. Alternatively, the thermistor might be faulty and needs replacement. A shorted heater can also trigger this error, in which case you should replace the heater. Lastly, the relay circuit could be the source of the problem, so repair the relay circuit.
Why does my LG LD-1415M1 show an EXCESS ERROR?
An EXCESS ERROR on your LG Dishwasher suggests a problem with one of several components. The inlet valve may be faulty and needs replacement. The air break could also be the issue, requiring you to replace the air breaker. Another possibility is a problem with the sensor assembly, which would mean replacing the sensor assembly. Finally, the controller itself might be malfunctioning, so you may need to repair or replace the controller.
General| Brand | LG |
|---|---|
| Model | LD-1415M1 |
| Category | Dishwasher |
| Language | English |
Service information for individuals with adequate electrical, electronic, and mechanical experience.
Covers High Temperature Rinsing and Turbo Spray System features.
Details the functions and indicators on the dishwasher's display panel.
Explains indicators, buttons like Program, Child Lock, Beep On/Off, and Power.
Describes the buttons, display, and operations for the test mode.
Step-by-step guide for completely disassembling the dishwasher.
Instructions for removing the balance weight and door assembly.
Procedures for removing fan, dispenser, door spring and door liner.
Instructions for removing the base spacer and tub assembly parts.
Steps for removing the tub and the air guide assembly.
Details on disassembling synchronous motor, vario valve, capacitor, and power cord.
Instructions for removing the Aquastop and drain hose.
Specific instructions for disassembling the C-base assembly.
Steps for removing side screws and disconnecting wires between tub and base.
Instructions for disconnecting wires from the inlet valve or Aquastop.
Lists error messages, possible causes, and remedies for common issues.
Diagnoses and repairs for "No Power" and "Power Button" related issues.
Diagnoses and repairs for the symptom "The Wash Pump/Motor does not run".
Addresses issues with washing results and dry results.
Details requirements for preparing the cupboard opening for installation.
Instructions for electrical wiring and installing the dishwasher into the cupboard.
Guidance on connecting the drain hose to the sink or standpipe.
Instructions for connecting water supply and performing final checks.
Exploded view of the upper and lower rack components.
Detailed exploded view of the tub assembly parts.
Exploded view of the panel and door assembly components.
Exploded view of the base assembly parts.
Detailed exploded view of the sump assembly components.
To Next Page
