J
Judy LopezSep 23, 2025
What to do if my LG Washer shows a PF error?
- LLouis Brady DDSSep 23, 2025
If your LG Washer displays a PF POWER FAILURE, it means that the appliance experienced a mains power failure. Restart the cycle.
To Next PageTo Next PageWhat to do if my LG Washer shows a PF error?
If your LG Washer displays a PF POWER FAILURE, it means that the appliance experienced a mains power failure. Restart the cycle.
Why is my LG Washer not working?
There are several reasons why your LG Washer might not be operating. First, ensure the control panel hasn't powered off due to inactivity by pressing the Power button. Check that the appliance is securely plugged into a working outlet and the water supply is fully turned on. Make sure the programme is correctly set, the door is properly closed, and the Start/Pause button is pressed. Also, inspect your house circuit breakers/fuses and reset them if necessary. If these steps don't work, try resetting the control by pressing the Power button, reselecting the programme, and pressing Start/Pause. In case of extremely low water pressure, check another tap in the house. Finally, remember that the drum may stop temporarily during heating or steaming cycles.
Why is my LG WV7-1410W Washer leaking water?
If your LG Washer is leaking, it could be due to several reasons. Check for clogged house drain pipes and unclog them, contacting a plumber if needed. Also, inspect the drain hose for improper installation or clogs; clean and straighten it, and regularly check the drain filter. Ensure the drain pump filter cap is correctly fitted.
What to do if my LG WV7-1410W Washer shows a UE error?
If your LG Washer displays a UE UNBALANCE ERROR, it means the load is unbalanced. The clothes may be too wet at the end of the cycle. Rearrange the load to allow proper spinning. Close the door and press Start/Pause button. It may take a few moments before the appliance begins to spin. The door must be locked before spin can be achieved. If the load is too small, add 1 or 2 similar items or smaller articles of clothes to help balance the load. Close the door and press Start/Pause button. It may take a few moments before the appliance begins to spin. The door must be locked before spin can be achieved.
Why is my LG Washer not filling with water properly?
If your LG Washer is not filling properly, start by checking if the inlet filters on the fill valves are clogged. Also, inspect the inlet hoses for any kinks or clogs. Ensure that both hot and cold water taps are fully turned on. Finally, verify that the hot and cold supply hoses are correctly connected.
Why is the cycle end delayed on my LG WV7-1410W Washer?
If the cycle end is delayed on your LG Washer, it is normal because unbalance is detected or suds removing programme is on. The time remaining shown on the display is only an estimated duration. Actual time may vary.
What does LE error mean on LG WV7-1410W Washer?
If your LG Washer displays a LE MOTOR LOCKED ERROR, it indicates an overload in motor. Let the appliance wait for 30 minutes until the motor is cooled down and then, restart the cycle.
Why are my clothes getting stained in my LG Washer?
Staining in your LG Washer can occur if bleach or softener is dispensed too soon, so dispenser compartment is overfilled, it makes bleach or softer dispensed rapidly, always measure bleach or softener to prevent overfilling and close the detergent dispenser slowly. If bleach or softener was added directly to the clothes in the drum, always use the detergent dispenser to ensure that bleach or softener is properly dispensed at the right time in the programme. If clothes were not properly sorted, always wash dark colours separately from light colours and whites to prevent discoloration and never wash heavily soiled items with lightly soiled items.
Why is my LG Washer making a rattling noise?
If your LG Washer is making a rattling or clanking noise, there might be foreign objects like keys, coins, or safety pins in the drum. Stop the appliance and check the drum for such objects. If the noise continues after restarting, call for service.
Why is my LG WV7-1410W Washer making a vibrating noise?
A vibrating noise in your LG Washer can be caused by several factors. First, make sure all package materials have been removed. If not, remove package materials. The clothes may be unevenly distributed in the drum. Pause the programme and redistribute the clothes after the door unlocks. Ensure all levelling feet are resting firmly and evenly on the floor; refer to the Levelling the Appliance instructions for adjustment. Also, check if the floor is solid and doesn't flex; see the Installation Place Requirements to select the proper location.
General| Type | Front Load |
|---|---|
| Capacity | 10.5 kg |
| Energy Rating | A+++ |
| Spin Speed | 1400 RPM |
| Color | White |
| Energy Efficiency Class | A+++ |
| Noise Level Spinning | 74 dB |
| Steam Function | Yes |
| Inverter Direct Drive | Yes |
| Smart Diagnosis | Yes |
| Inverter Motor | Yes |
| Smart Function | Yes |
| Wi-Fi Enabled | Yes |
