Life Fitness X 5 User Manual (English)

Other manuals for Life Fitness X 5

Owner's Manual28 pages

Assembly Instructions20 pages

User Manual23 pages

Assembly & Operation Manual28 pages

Questions and Answers:

M
Melissa McmillanAug 17, 2025
Why is the wireless heart rate not working on my Life Fitness Elliptical Trainer?
- C
  christinemillsAug 18, 2025
  If the wireless heart rate is not working on your Life Fitness Elliptical Trainer, first, ensure that the WIRELESS HR is turned ON in the Settings Menu. Also, poor contact between the telemetry heart rate strap and the skin can be the cause. Electrical interference from appliances or fluorescent lights can also interfere, so try moving the elliptical or appliances. Finally, the battery in the Heart Rate Telemetry Strap (CR2032 3V) may need to be replaced.
G
Gina LongAug 20, 2025
How to troubleshoot no power on Life Fitness Elliptical Trainer?
- E
  eharrisAug 20, 2025
  If your Life Fitness Elliptical Trainer has no power, check that the power cord is fully plugged into both the back of the elliptical and the wall. Also, verify that you are not in “Energy Saver Mode” by pressing the “Energy Saver” button. Finally, ensure all customer assembly connections are working properly by unplugging and re-plugging each connection, and check for any pinched cables.
S
Savannah WilliamsonAug 22, 2025
What to do if start-up resistance is too difficult on Life Fitness Elliptical Trainer?
- M
  Michael KramerAug 22, 2025
  If the start-up resistance on your Life Fitness Elliptical Trainer seems very difficult, it may be in ‘Safety Mode’. Refer to the console manual on how to turn off this setting. If that's not the case, try turning the unit off and then on again.
N
Nancy KennedyAug 25, 2025
What to do if the Life Fitness Fitness Equipment console is out?
- M
  meredith64Aug 26, 2025
  If the console of your Life Fitness Fitness Equipment is non-operative, first check that the transformer is plugged in and that the wiring harness is connected to the console. Inspect the wiring harness in the upright tube or at the base frame to ensure proper connections. If connections are correct, replace the transformer. If the issue persists, replace the console. This may be due to the transformer not being plugged in, the wiring harness not being connected, or pinched wire harnesses.
M
Michael LopezAug 27, 2025
Why is there no speed readout on the Life Fitness Fitness Equipment console (Version 2)?
- M
  Mary LewisAug 27, 2025
  If you're not getting a speed readout on your Life Fitness Fitness Equipment console (Version 2), the magnet may be missing, or the reed switch could be faulty. Check for a missing magnet or replace the switch.
D
daveellisAug 30, 2025
What to do if Life Fitness Fitness Equipment makes a metallic scraping noise?
- J
  Jenna MendezAug 30, 2025
  If your Life Fitness Fitness Equipment is making a metallic scraping noise in either the forward or reverse direction (Version 1 units only), the magnet might be rubbing on the aluminum disk, or the chopper wheel may be hitting the OPTO Sensor. Remove the bottom rear shroud and inspect the position of the magnets to see if they are rubbing on the aluminum disk. If they are, re-center the OPTO Sensor.
M
Mr. Wayne WareSep 1, 2025
How to fix clunking noise in Life Fitness Fitness Equipment?
- D
  Deborah WebbSep 1, 2025
  To address a clunking noise in your Life Fitness Fitness Equipment, remove the clevis covers and check for damaged washers, retaining rings, and wave springs. Replace them if necessary. Remove the end caps from the lower link arm, then remove the bolt. Ensure the retaining ring is correctly installed. Repeat this process for all pivot areas. The noise may be caused by damaged washers, retaining rings, or wave springs.
C
Catherine RoachSep 4, 2025
Why is there no speed readout on the Life Fitness Fitness Equipment console (Version 1)?
- K
  Kara PadillaSep 4, 2025
  If there is no speed readout on the console of your Life Fitness Fitness Equipment (Version 1), verify that the connections between the OPTO sensor and wiring harness are secure. Also, the chopper wheel might not be spinning between the two tabs of the OPTO sensor; if so, bend the OPTO bracket slightly upwards. This issue may arise from loose connections between the OPTO sensor and wiring harness, or the chopper wheel not spinning correctly.
D
Daniel BellSep 6, 2025
How to fix a bump in the pedal motion of Life Fitness Fitness Equipment?
- S
  Susan GonzalezSep 6, 2025
  To fix a slight bump or hitch in the pedal motion of your Life Fitness Fitness Equipment, remove all clevis covers and loosen all six bolts that connect links to clevis brackets. Loosen the nuts a couple of turns so the machine can still be operated. Operate the machine a few revolutions to help seat the pivot points, then retighten the six bolts and install the clevis covers. Also, ensure the levelers are in contact with the floor and that the leveler jam nuts are properly tightened. The issue may be due to pivot points not being broken in or levelers not being in contact with the floor.
K
Katie RandallSep 9, 2025
How to fix loose total body arms on Life Fitness Elliptical Trainer?
- B
  Beth OwensSep 9, 2025
  If the total body arms feel loose on your Life Fitness Elliptical Trainer, remove the moving arm pivot covers and check that the bolt holding the total body arm in place is fully tightened. If they still feel loose, disassemble the total body arms and ensure all the proper hardware from the assembly instructions was used.

Life Fitness X 5 Specifications

General

Type	Front-Drive
Resistance Levels	20
Stride Length	20 inches
Display	LCD
Programs	Manual, Random, Hill, Cardio, Fat Burn
Heart Rate Monitoring	Contact Grips and Wireless Compatible
User Profiles	2