To Next PageTo Next PageWhat to do if my Lincoln Electric Power MIG 350MP shows error 39?
Error 39 in your Lincoln Electric Welding System is possibly caused by noise or a signal level issue. Make sure that the machine is properly grounded. If the problem continues, contact an authorized Lincoln Field Service Shop.
What to do if my Lincoln Electric Power MIG 350MP shows error 47?
Error 47 in your Lincoln Electric Welding System is possibly caused by noise or a signal level right at the trip threshold. If the problem persists, contact an authorized Shop.
What to do if Lincoln Electric Welding System shows error 44?
If your Lincoln Electric Welding System displays error 44, check the machine ground.
What to do if Lincoln Electric Power MIG 350MP shows error 81?
If your Lincoln Electric Welding System displays error 81: * Verify that the motor armature is not binding. * Verify that the wire spool is not binding.
What to do if Lincoln Electric Power MIG 350MP shows error 82?
If your Lincoln Electric Welding System displays error 82: * Verify that the wire can move freely in the cable. * Verify that the spool brake is not set too tight.
General| Input Voltage | 208/230/460 V |
|---|---|
| Output Amperage Range | 30 - 350 A |
| Output Current Range | 30 - 350 A |
| Input Current | 32A at 230V, 16A at 460V |
| Rated Output | 300 A at 26 V, 60% Duty Cycle |
| Input Current at Rated Output | 32A at 230V, 16A at 460V |
| Welding Processes | MIG, Flux-Cored, Stick, TIG |
| Weight | 220 lbs (100 kg) |
| Wire Feed Speed Range | 50-800 IPM (1.27-20.32 m/min) |
| Duty Cycle | 60% at 350A |
| Wire Diameter Range | 0.023" - 0.045" (0.6mm - 1.2mm) |
Legal warnings required by California regarding potential health risks from product use.
Key safety warnings covering electric shock, fumes, sparks, and arc rays associated with welding.
Safety guidelines for engine-powered equipment and awareness of Electric and Magnetic Field (EMF) hazards.
Essential safety measures for handling compressed gas cylinders and operating electrical equipment.
Detailed technical data including voltage, current, physical dimensions, and wire speed.
Guidelines for connecting the welder to the power supply, including voltage and grounding.
Procedures for installing the welding gun, cable, and connecting the shielding gas supply.
Instructions for connecting an air-cooled TIG torch for DC TIG welding operations.
Critical safety measures to be followed during the operation of the welding machine.
Explanations of different welding modes, definitions, and common welding abbreviations.
Overview of the machine's controls, displays, and the multi-process panel layout.
Step-by-step guide to setting welding parameters using the machine's controls and panel.
Instructions for wire loading, setting pressure, and preventing wire feeding issues.
Detailed explanations of special welding processes like Pulse, Pulse-on-Pulse, and Power Mode.
Information on available drive roll kits, aluminum feeding kits, and spool gun compatibility.
Details on Magnum GMAW guns, cable assemblies, and connection kits for the welder.
Information on push-pull torches, TIG torches, and optional kits like the Dual Procedure Kit.
Essential safety warnings before performing any maintenance tasks on the welding equipment.
Routine cleaning of the welder, fan motors, and general parts for optimal performance.
Instructions for installing, cleaning, and maintaining contact tips and gas nozzles.
Procedures for cleaning the gun cable liner and replacing it when necessary.
General safety advice and instructions on how to effectively use the troubleshooting guide.
Solutions for issues such as no power, no welds, or low output from the machine.
Diagnostic steps for resolving problems concerning wire feeding and shielding gas flow.
Understanding and resolving specific fault codes and display messages shown on the machine.
Specific guidance for diagnosing and fixing wire feeding problems with push-pull torches.
Procedures for resetting the machine and adjusting the stall factor for optimal performance.
Detailed electrical schematic illustrating the internal wiring and connections of the welding machine.
