Need help?Do you have a question about the Line 6 POD HD and is the answer not in the manual?
General| MIDI | MIDI In/Out |
|---|---|
| Type | Multi-effects processor |
| Looper | Yes |
| Presets | 128 |
| Amp Models | 16 |
| Inputs | 1 x 1/4" Guitar, 1 x XLR Mic |
| Outputs | XLR |
| USB | USB |
| Display | LCD |
| Power Supply | DC power supply |
| Effects Types | Distortion, Modulation, Delay, Reverb |
| Expression Pedal | Built-in |
Explains how to access and navigate through different Home View screens.
Details the Signal Flow View, showing FX and Amp Blocks and their positions.
Describes accessing and editing parameters using the multi-function knobs.
Details the Big User View for a large display of the current Preset number.
Explains the Performance View screens and their variations based on settings.
Details how to enter and use the Tuner mode with available options.
Explains how to set the system tempo using the TAP button or Setup menu.
Refers to the Pilot's Guide for details on input and output connections.
Introduces the Line 6 POD HD Edit software for patch editing and management.
Instructions on how to enter the System Setup menu and navigate its pages.
Details footswitch mode, amp knobs display, and looper FS display settings.
Covers LCD contrast, tap tempo LED, AC frequency, and FBV express settings.
Explains selecting input sources and adjusting guitar input impedance (In-Z).
Describes how input signals are routed through Amp & FX Blocks in the 'Pre' position.
Details output modes for direct recording or connecting to an external amplifier.
Configuration for S/PDIF output, including match outputs and sample rate.
Settings for tempo sync, preset tempo, and global tempo information.
Details on selecting FX models, parameters, and managing DSP usage.
Explains Amp Block placement, toggling, and editable parameters.
Details on the Mixer Block's Level and Pan controls for parallel paths.
Instructions on repositioning FX Blocks for flexible signal routing.
Explains how mono and stereo FX/Amp models affect signal routing.
How to assign Amp or FX parameters to the TWEAK knob.
Configuring footswitch assignments for FX and Amp Blocks.
Explains the Dynamic DSP system and managing DSP limit reached.
How POD HD stores and accesses Presets via Set Lists.
Steps to rename a Set List using the SAVE button.
How to rearrange Presets within a Set List.
Instructions for loading and repositioning Presets within Set Lists.
Details on navigating and saving Presets from Home View screens.
Using A, B, C, D buttons and Bank Up/Down for Preset navigation.
Procedure for saving a Preset, including naming and destination selection.
Steps to enter FX Edit Mode from the Signal Flow View.
Using Knob 1 to choose the FX Model category or 'None'.
Using Knob 2 to select a specific FX Model within the chosen type.
Using Knob 3 to select parameters and Knob 4 to adjust their values.
Explains how to position Amp Blocks in the signal chain (Pre, Post, Paths A/B).
Details using a single Amp Block in either the Pre or Post signal path.
Procedure for selecting Amp, Cab, and Mic models via the Signal Flow View.
Details on Preamp versions of amps for external amplifier use.
Describes the three states of an Amp Block: On, Off (bypassed), or Disabled.
Explains automatic selection of Cab/Mic models and tone settings.
Lists available Mic Models for Guitar and Bass Amp cabinets.
How to toggle Amp models on/off and adjust Amp Tone knob settings.
Accessing the Amp & Cab Edit screens for detailed parameter tuning.
Details power amp characteristics like Master Volume, Sag, and Heater Hum.
Covers Microphone, Speaker Cabinet, and Resonance settings.
Describes non-standard Amp Tone knob labels for specific models.
Lists classic speaker cabinets and their original models.
Reference table for Dynamics FX models and their common parameters.
Reference table for Distortion FX models and their common parameters.
Reference table for Modulation FX models and their common parameters.
Reference table for Filter FX models and their common parameters.
Reference table for Pitch FX models and parameter descriptions.
Reference table for Preamp+EQ FX models and common parameters.
Reference table for Delay FX models and their common parameters.
Reference table for Reverb FX models and their common parameters.
Details on Volume/Pan FX models and their use with FBV pedals.
Explains the Volume parameter and its access via multi-function knobs.
Describes the Pan parameter and its effect on stereo signal balance.
Reference table for Wah FX models and their parameters.
Overview of Looper controls via POD HD buttons and the Performance View.
Explains setting the Looper Block to 'Pre' or 'Post' in the signal chain.
Instructions on recording loops and layering overdubs.
Controls for playing, stopping, half speed, and reversing recorded loops.
Details on adjusting Looper playback volume and EQ settings.
Explains the impact of Full Speed and 1/2 Speed on recording time and playback.
Prerequisites for using POD HD as an audio interface via USB.
Diagram and explanation of USB audio routing between POD HD and computer.
How the Record Send provides processed signal to audio software.
Interface for configuring audio driver settings on Mac and Windows.
Detailed settings for Mac audio interface configuration.
Configuration options for Windows systems using the audio driver utility.
Configuration for ASIO driver settings like buffer size and bit depth.
Adjusting buffer size for audio responsiveness and latency.
Instructions to launch the Line 6 Monkey updater software.
Steps to create or log in to a Line 6 Monkey account.
Process for registering connected Line 6 hardware.
How to check for and install available firmware or software updates.
Information on keeping current presets during flash memory updates.
Introduction to supported FBV controllers like the Shortboard MkII.
Instructions for connecting FBV devices using RJ-45 cables.
Setup options affecting POD HD behavior when an FBV device is connected.
Visual references for FBV footswitch assignments in Performance View.
Mapping tables for FBV Shortboard MkII footswitches and pedals.
Footswitch mappings for Looper functions on FBV controllers.
Mapping tables for FBV Express MkII footswitches and pedals.
Mapping tables for FBV Longboard footswitches and pedals.
Steps to assign EXP 1 and EXP 2 controllers to Amp/FX parameters.
Configuring FBV footswitches to toggle Amp or FX Blocks On/Off.
Manually assigning the pedal's Toe Switch to toggle FX Blocks.
How to access and load Set Lists from FBV Shortboard/Longboard.
Using the TAP footswitch to set the tempo on FBV devices.
Entering Tuner mode by pressing and holding the TAP button on FBV.
To Next Page