LTC6804-1/LTC6804-2
53
680412fc
For more information www.linear.com/LTC6804-1
operaTion
Table 46. Memory Bit Descriptions
NAME DESCRIPTION VALUES
GPIOx GPIOx Pin Control Write: 0 -> GPIOx Pin Pull-Down ON; 1-> GPIOx Pin Pull-Down OFF (Default)
Read: 0 -> GPIOx Pin at Logic 0; 1 -> GPIOx Pin at Logic 1
REFON Reference
Powered Up
1 -> Reference Remains Powered Up Until W
atchdog Timeout
0 -> Reference Shuts Down after Conversions (Default)
SWTRD
SWTEN Pin Status
(Read Only)
1 -> SWTEN Pin at Logic 1
0 -> SWTEN Pin at Logic 0
ADCOPT
ADC Mode Option
Bit
ADCOPT: 0 -> Selects Modes 27kHz, 7kHz or 26Hz with MD[1:0] Bits in ADC Conversion Commands (Default).
1 -> Selects Modes 14kHz, 3kHz or 2kHz with MD[1:0] Bits in ADC Conversion Commands.
VUV Undervoltage
Comparison
Voltage*
Comparison voltage = (VUV + 1) • 16 • 100µV
Default: VUV = 0x000
VOV Overvoltage
Comparison
V
oltage*
Comparison voltage = VOV • 16 • 100µV
Default: VOV = 0x000
DCC[x]
Discharge Cell x x = 1 to 12 1 -> Turn ON Shorting Switch for Cell x
0 -> Turn OFF Shorting Switch for Cell x (Default)
DCTO Discharge Time
Out Value
DCTO
(Write)
0 1 2 3 4 5 6 7 8 9 A B C D E F
Time
(Min)
Disabled 0.5 1 2 3 4 5 10 15 20 30 40 60 75 90 120
DCTO
(Read)
0 1 2 3 4 5 6 7 8 9 A B C D E F
Time
Left
(Min)
Disabled
or
Timeout
0
to
0.5
0.5
to
1
1
to
2
2
to
3
3
to
4
4
to
5
5
to
10
10
to
15
15
to
20
20
to
30
30
to
40
40
to
60
60
to
75
75
to
90
90
to
120
CxV Cell x V
oltage*
x = 1 to 12 16-Bit ADC Measurement Value for Cell x
Cell Voltage for Cell x = CxV • 100µV
CxV Is Reset to 0xFFFF on Power-Up and After Clear Command
GxV GPIO x Voltage* x = 1 to 5 16-Bit ADC Measurement Value for GPIOx
Voltage for GPIOx = GxV • 100µV
GxV Is Reset to 0xFFFF on Power-Up and After Clear Command
REF 2nd Reference
Voltage*
16-Bit ADC Measurement Value for 2nd Reference
Voltage for 2nd Reference = REF • 100µV
Normal Range Is within 2.985V to 3.015V
SOC Sum of Cells
Measurement*
16-Bit ADC Measurement Value of the Sum of All Cell Voltages
Sum of All Cells Voltage = SOC • 100µV • 20
ITMP Internal Die
Temperature*
16-Bit ADC Measurement Value of Internal Die Temperature
Temperature Measurement (°C) = ITMP • 100µV/7.5mV/°C – 273°C
VA Analog Power
Supply Voltage*
16-Bit ADC Measurement Value of Analog Power Supply Voltage
Analog Power Supply Voltage = VA • 100µV
Normal Range Is within 4.5V to 5.5V
VD Digital Power
Supply Voltage*
16-Bit ADC Measurement Value of Digital Power Supply Voltage
Digital Power Supply Voltage = VA • 100µV
Normal Range Is within 2.7V to 3.6V
CxOV Cell x Overvoltage
Flag
x = 1 to 12 Cell Voltage Compared to VOV Comparison Voltage
0 -> Cell x Not Flagged for Overvoltage Condition. 1 -> Cell x Flagged
CxUV Cell x
Undervoltage Flag
x = 1 to 12 Cell Voltage Compared to VUV Comparison Voltage
0 -> Cell x Not Flagged for Undervoltage Condition. 1 -> Cell x Flagged
REV Revision Code Device Revision Code. See Revision Code and Reserved Bits in Operation Section.
RSVD Reserved Bits See Revision Code and Reserved Bits in Operation Section.
To Next Page
Loading...