Lippert SureShade Power Bimini

Other manuals for Lippert SureShade Power Bimini

Installation Manual22 pages

Frequently Asked Questions3 pages

Questions and Answers

P
paige65Aug 18, 2025
Why is the top of my Lippert Industrial Equipment not raising or lowering?
- L
  Laura WhiteAug 18, 2025
  If the top on your Lippert Industrial Equipment isn't raising or lowering, here's what you can check: * Ensure the boat's electrical power is on. * Inspect for loose or unconnected wires and connect them properly. * If these steps don't resolve the issue, it could be due to a pinched/cut harness wire, in which case the wire harness should be replaced. For bad electrical harness or controller contact Lippert. Email: customerservice@lci1.com Phone: 432-LIPPERT (432-547-7378).
K
katiejohnsonAug 20, 2025
What to do if the controller buttons on my Lippert Industrial Equipment do not respond?
- U
  uandradeAug 20, 2025
  If the controller buttons on your Lippert Industrial Equipment aren't responding, try the following: * Make sure the boat's electrical power is turned on. * Check for any loose or unconnected wires and ensure they are properly connected. * If there is a pinched or cut harness wire, replace the wire harness. If the problem persists, it may be a bad controller. Contact Lippert. Email: customerservice@lci1.com Phone: 432-LIPPERT (432-547-7378).
S
Samantha ShepherdAug 23, 2025
Why is the controller power indicator light not lit on my Lippert Industrial Equipment?
- B
  Barbara PorterAug 23, 2025
  If the controller power indicator light is not lit on your Lippert Industrial Equipment, ensure that the boat's electrical power is turned on. If the light still doesn't come on, the controller needs to be replaced.
C
Cody BradyAug 26, 2025
What to do if fly extension stanchions do not reach the locking plates on my Lippert Industrial Equipment?
- N
  Nicholas ButlerAug 26, 2025
  If the fly extension stanchions on your Lippert Industrial Equipment do not reach the locking plates, make sure the fly extension and the Bimini top are fully extended. If the issue remains, relocate the locking plates.
D
Daniel HowellAug 28, 2025
How to fix a mesh top that sags on Lippert Industrial Equipment?
- H
  hgutierrezAug 28, 2025
  If the mesh top on your Lippert Industrial Equipment is sagging, ensure all frame pockets are zipped closed, all snaps are connected, and the mesh top is fully opened.
B
Brian RodriguezAug 30, 2025
What to do if the tie-down strap does not reach the saddle on my Lippert Industrial Equipment?
- A
  Anthony HamiltonAug 30, 2025
  If the tie-down strap on your Lippert Industrial Equipment does not reach the saddle, relocate the saddle. Alternatively, adjust the tie-down strap buckle to increase the strap length.
J
Joseph ShieldsSep 2, 2025
What to do if the tie-down strap clip does not close on the saddle or stanchion of my Lippert Industrial Equipment?
- C
  Craig HoffmanSep 2, 2025
  If the tie-down strap clip on your Lippert Industrial Equipment does not close on the saddle or stanchion, replace the tie-down strap.
T
Tracy SmithSep 4, 2025
Why my Lippert SureShade Power Bimini Bimini top will not open?
- P
  Pamela LeonardSep 4, 2025
  If your Lippert Boating Equipment Bimini top isn't opening, there could be a few reasons. First, ensure that the battery is fully charged, as low power can prevent it from opening. Another potential cause is a lack of power. In this case, check the electrical connections at the actuator and helm switch, and reconnect any loose or disconnected connections. Also, inspect the electrical connections for any nicks or cuts and repair or replace them as needed.
D
Daniel SmithSep 7, 2025
What to do if my Lippert SureShade Power Bimini Boating Equipment Bimini top will not close?
- H
  Henry AndersonSep 7, 2025
  If your Lippert Boating Equipment Bimini top isn't closing, several factors could be at play. Initially, ensure the battery is fully charged, as low power can hinder its operation. Also, check the actuator and helm switch electrical connections, reconnecting any that are loose or disconnected. Inspect all electrical connections for damage, repairing or replacing as necessary. Furthermore, a damaged actuator or foreign material blocking the gear handle could be the cause. If the actuator is damaged or the gear handle is blocked, perform a manual override after removing any obstructions.
J
James WebbSep 9, 2025
How to fix Lippert SureShade Power Bimini Boating Equipment Bimini top that does not fully open?
- W
  Willie HendersonSep 10, 2025
  If your Lippert Boating Equipment Bimini top isn't fully opening, start by checking the battery to ensure it's fully charged. Low power can prevent the top from fully opening. Then, inspect the electrical connections at the actuator and helm switch, reconnecting any loose connections. Also, examine the wiring for any nicks or cuts, repairing or replacing damaged sections. A damaged actuator or obstructions in the gear handle could also be the reason. If the actuator is damaged or the gear handle is blocked, perform a manual override after removing any obstructions.