LongerPump BT100-1F - Suitable Pump Head and Tubing

Flow Rate Display
b.
c.
d.
e.
Running Interface
Turn on the pump, the pump initializes itself first then display the running interface.
a.
3 4
7.000 mL/min
50.0
INT
g.
f.
Vol 13.0 mL：
Copy 9999：
b.
c.
e.
h.
c.
e.
Disp T. 79.0"：
100 RPM
Dispensing Display: Dispensing status is displayed by two interfaces below,
these interface can be switched by pressing .Exit Key
Suitable Pump Heads and Tubing
Suitable Pump Heads
Tubing (mm)
Ref. Flow Rate(mL/min)
15
#
#
24
0.17-170
0.29-290
13
14
19
16
25
17
18
#
#
#
#
#
#
#
YZ2515
YZ 25
x
Ⅱ
==
DG-1/2/4(10 )Rollers
DG-1/2/4(6 )Rollers
7 L-7mL/min
0.027-27
0.051-51
0.082-82
0.17-170
0.29-290
0.38-380
μ
15
24
5
#
#
#
#
3
36
0.17-170
0.29-290
0.38-380
0.50-500
0.13 0.91
0.25 0.91
0.51 0.91
1.02 0.86
1.65 0.86
2.4 0.8
2.79 0.86
3.17 0.86
×
×
×
×
×
2×1
×
×
×
0.13 0.91
0.25 0.91
0.51 0.91
1.02 0.86
1.65 0.86
2.4 0.8
2.79 0.86
3.17 0.86
×
×
×
×
×
2×1
×
×
×
0.25 L/min-160 L/min
0.52 L/min-520 L/min
2.0 L/min-2.0mL/min
4.6 L/min-4.6mL/min
0.014 - 14
0.016 - 16
0.022 - 22
0.028 - 28
0.035 - 32
μμ
μμ
μ
μ
0.16 L/min-160 L/min
0.56 L/min-560 L/min
2.2 L/min-2.2mL/min
5.8 L/min-5.8mL/min
0.018-18
0.02-21
0.026-26
0.035-35
0.044-44
μμ
μμ
μ
μ
a. Current flow rate: Display current flow rate. Turning the can increase or
decrease the flow rate.
b. Current speed: Display current speed. the can increase or
decrease the speed.
c. Running direction: Indicate the direction of the pump.
d. Running status: stands for pump running; stands for pump stopping;
Stands for pump pausing. Press to control the working state of
the pump.
e. Control Mode: stands for internal control mode; stands for closing the
external control by setting menu; stands for inserting analog voltage input
control module into ; stands for inserting analog
current control module into ; stands for inserting 0-10
KHz frequency input module into .
f. Dispensing Volume: Display dispensing volume under dispensing mode.
g. Copy number: Display copy number under dispensing mode.
h. Dispensing time: Display the dispensing time. When the dispensing procedure
starts, the dispensing time will count down. Adjust the Flow rate to change
Dispensing time in dispensing parameters setting interface.
Knob
Knob
Start/Stop Key
INT Off
V
External Control Port mA
External Control Port Hz
External Control Port
Turning
YZ1515 YZ 15x Ⅱ
Pump heads and tubing can be selected referring to above table. It is necessary to
select suitable pump heads and tubing to get higher flow rate and higher dispensing
accuracy. We suggest your needed flow rate range is in the range of 20% to 80% of
ref. flow rate range.
BT100-1F OPERATING MANUAL
BT100-1F OPERATING MANUAL