EasyManuals Logo

LOVATO ELECTRIC DCRG8 Instruction Manual

LOVATO ELECTRIC DCRG8
37 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Doc: I340PLGB1012_DCRG8 30/10/2012 s. 1 / 37
PL
DCRG8 DCRG8
Automatyczny regulator Automatic Power Factor Controller
współczynnika mocy
INSTRUKCJA OBSŁUGI INSTRUCTIONS MANUAL
Przed pracami serwisowymi, należy odłączyć wszystkie napięcia od wejść pomiarowych
i zasilania pomocniczego oraz zewrzeć zaciski przekładnika prądowego.
Produkty zaprezentowane w poniższym dokumencie mogą zostać zmienione lub ulepszone
bez konieczności wcześniejszego informowania o tym.
Dane techniczne oraz opisy oddają w jak najdokładniejszy sposób posiadaną przez nas
wiedzę, jednak nie bierzemy odpowiedzialności za ewentualne błędy, braki oraz sytuacje
awaryjne.
W układzie należy zamontować rozłącznik (wyłącznik), który musi znajdować się niedaleko
urządzenia i być łatwo dostępny dla operatora. Musi spełniać wymogi następujących norm:
IEC/ EN 61010-1 § 6.12.2.1.
Należy czyścić urządzenie delikatną suchą szmatką, nie należy u
żywać środków ściernych,
płynnych detergentów lub rozpuszczalników.
Before any maintenance operation on the device, remove all the voltages from measuring
and supply inputs and short-circuit the CT input terminals.
Products illustrated herein are subject to alteration and changes without prior notice.
Technical data and descriptions in the documentation are accurate, to the best of our
knowledge, but no liabilities for errors, omissions or contingencies arising there from are
accepted.
A circuit breaker must be included in the electrical installation of the building. It must be
installed close by the equipment and within easy reach of the operator.
It must be marked as the disconnecting device of the equipment:
IEC /EN 61010-1 § 6.12.2.1.
Clean the instrument with a soft dry cloth; do not use abrasives, liquid detergents or
solvents
.
Spis treści Strona
Wprowadzenie 2
Opis 2
Funkcje przycisków 2
Wskaźniki LED 3
Tryby pracy 3
Menu główne 4
Hasło dostępu 4
Nawigacja po wyświetlanych stronach 5
Tabela wyświetlanych stron 5
Strona analizy harmonicznych 7
Strona przebiegów 7
Możliwość rozbudowy 8
Dodatkowe zasoby 9
Kanały komunikacji 9
Wejścia, wyjścia, zmienne wewnętrzne, liczniki 9
Progi limitów 10
Zmienne kontrolowane zdalnie 11
A
larmy użytkownika 11
Konfiguracja Master / Slave 11
Port podczerwieni do programowania 13
Ustawianie parametrów przez PC 14
Ustawianie parametrów przez panel przedni
15
Tabela parametrów 17
A
larmy 26
Opis alarmów 26
Właściwości alarmów 27
Tabela właściwości alarmów 28
Tabela funkcji wejść 28
Tabela funkcji wyjść 28
Tabela pomiarów limitów i wyjść analogowych 29
Menu komend 30
Instalacja 30
Schematy podłączeń 31
Opis zacisków 36
Wymiary mechaniczne i otwór montażowy
36
Dane techniczne 37
Historia wersji instrukcji 37
Index
Page
Introduction
2
Description
2
Keyboard functions
2
Front LED indication
3
Operating modes
3
Main menu
4
Password access
4
Display page navigation
5
Table of display pages
5
Harmonic analysis page
7
Waveform pages
7
Expandability
8
A
dditional resources
9
Communication channels
9
Inputs, outputs, internal variables, counters 9
Limit thresholds
10
Remote-controlled variables
11
User alarms
11
Master Slave Configuration
11
IR programming port
13
Parameter setting through PC
14
Setting of parameters (setup) from front panel 15
Parameter table
17
A
larms
26
A
larm description
26
A
larm properties
27
A
larm table
28
Input function table
28
Output function table
28
Measure table for limits and analog outputs 29
Command menu
30
Installation
30
Wiring diagrams
31
Terminal arrangement
36
Mechanical dimensions and Panel cutout 36
Technical carachteristics
37
Manual revision history
37
I340 PL GB 1012
UWAGA!
Należy uważnie przeczytać instrukcję przed instalacją lub użytkowaniem.
By uniknąć zniszczeń lub zagrożenia życia urządzenia powinny
być instalowane przez wykwalifikowany personel w zgodzie
z obowiązującymi standardami
WARNING!
Carefully read the manual before the installation or use.
This equipment is to be installed by qualified personnel, complying to
current standards, to avoid damages or safety hazards.

Other manuals for LOVATO ELECTRIC DCRG8

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the LOVATO ELECTRIC DCRG8 and is the answer not in the manual?

LOVATO ELECTRIC DCRG8 Specifications

General IconGeneral
BrandLOVATO ELECTRIC
ModelDCRG8
CategoryController
LanguageEnglish

Related product manuals