MAAX 102886 - User Manual

To Next Page













Save thiS guide for future reference.

conServer pour un uSage ultérieur.

conServe eSte manual como referencia.



       







Serial number  Numéro de série Número de Serie

important

important

importante

Main Page

Need help?

Do you have a question about the MAAX 102886 and is the answer not in the manual?

This document is an installation, usage, and maintenance guide for a MAAX Neo-angle corner shower kit, models 102886 and 102889.

Function Description:

The MAAX Neo-angle corner shower kit is designed to provide a functional and aesthetically pleasing showering space. It is a complete unit that includes a base, glass panels, and all necessary hardware for installation. The shower unit is intended for residential use, with specific commercial limitations outlined in the warranty. The neo-angle design is space-efficient, fitting into a corner while offering a wider entry than a standard square or rectangular corner shower. The door is designed to open outwards, requiring sufficient clear space for operation. The kit emphasizes ease of installation with detailed, step-by-step instructions, although it recommends professional plumbing and, for certain aspects, a two-person installation.

Important Technical Specifications:

Models: 102886, 102889
Drain Pipe: Requires an approximate internal diameter of 2" and an outside diameter of 2 3/8" for a snug seal and to prevent leakage. If the outside diameter is not 2 3/8", reducing fittings will be necessary. The drain pipe should be plumb and firmly in place, with a smooth, burr-free top.
Wall Requirements: Adjacent walls must be square and vertical (90° angle). The base must be installed directly against studs, not a finished wall.
Drill Bits: 1/8" and 1/4" for general drilling, and a 3/32" drill bit is provided for specific panel upright holes. A 1/4" masonry drill bit is recommended for ceramic tile installations.
Screws: #10 x 1 1/4" long screws for wall channels, #6 x 1/2" long screws for securing the shower to wall channels, and #10-24 x 1/2" long screws for pivot block installation. M5 x 1/4" setscrews are used for adjustable pivot bushings.
Caulking: Siliconized latex caulking (premium quality, mildew resistant) is required. Latex-based caulking is recommended for polystyrene wall panels due to better adhesion. Plumber's putty should NOT be used on polystyrene and ABS walls as it can cause severe cracking.
Materials: The unit utilizes high-quality materials, with strict quality control measures. Polystyrene is mentioned for wall panels, and glass for the door and fixed panels. Painted aluminum surfaces are also part of the construction.
Certifications: MAAX products are certified by one or more of the following agencies: CSA, UL, IAPMO, ULI, INTERTEK (ETL), WARNOCK HERSEY, US TESTING, and NAHB. Some models may be pending approval.

Usage Features:

Door Opening: The door can be configured to open either to the left (right-side hinging) or to the right (left-side hinging). It opens outwards, so sufficient space is needed.
Adjustable Door: The door features adjustable pivot bushings and an adjustment screw on the glass clamps, allowing for precise alignment to ensure it sits evenly against the handle-side sealing gasket. Adjustments should always be made from inside the shower to prevent scratching the rail.
Waterproofing: The design incorporates sealing gaskets for the bottom, hinge-side, and handle-side of the door, along with specific caulking instructions for both the inside and outside of the shower unit to ensure proper waterproofing.
Drain Location: The drain can be located to the left, middle, or right, depending on the unit, and its exact position (12 1/4" from each stud wall) is critical for proper installation.

Maintenance Features:

Regular Disinfection: Periodic disinfection is recommended to prevent bacterial growth in deposits that accumulate in showers.
Cleaning:
- Clear Panels, Base, and Walls: Can be cleaned with a mild detergent solution, rinsed well, and dried with a chamois or soft cloth. For stubborn stains, a window glass cleaner can be used, but the surface should be wiped immediately after application.
- Base, Walls, and Painted Aluminum Surfaces: Their luster can be restored with a mild automotive wax/polish. The wax helps fill small scratches, keeping surfaces cleaner longer. Rubbing compound should not be used, and any polish should be tested on a small, inconspicuous area first.
Prohibited Cleaners: Abrasive cleaners, scrapers, metal brushes, or any object/product that could scratch or dull the surface should NOT be used.
Stain Removal:
- Paint Stains: Use turpentine or a paint thinner.
- Joint Compound: Use a plastic or wood spatula covered with a damp cloth. Avoid metal blades or brushes.
Rubber Mats: If a rubber mat is used in the shower, it MUST be removed immediately after each use. Failure to do so will cause damage not covered by the warranty.
Gasket Replacement: Hinge-side and handle-side sealing gaskets should be removed before sealing the unit with silicone and replaced after the silicone has dried for 48 hours. The "U" shaped part of the hinge-side sealing gasket should be cut to the exact length of the glass door panel, ensuring a flap is left at both ends for waterproofing.