M150/M200 QUICK CARD
Form 169414 Rev. A Page 1 of 4
Supplement to M150/M200 Operator’s Manual. See manual for greater detail.
Break-In Period Services General Services
Lubricant Specifications Fluid Specifications
HRS ITEM CHECK
0.25
Road or
1 Field
Drive Wheel Nuts Torque - 175-200 ft-lb (237-271 Nm)
A/C Belt Tension Tension
Caster Wheel Nuts Torque - 115-127 ft-lb (156-172 Nm)
Caster Wheel Anti-
Shimmy
Dampener Bolts
Inboard Bolt Torque - 100 ft-lb (135 Nm)
Outboard Bolt Torque - 85 ft-lb (115 Nm)
5
Walking Beam Bolts Torque - 330 ft-lb (448 Nm)
Walking Beam Bolts Torque - 330 ft-lb (448 Nm)
Drive Wheel Nuts Torque - 175-200 ft-lb (237-271 Nm)
10
Neutral Dealer Adjust if Required
Hose Clamps - Air
Intake, Radiator,
Heater, Hydraulic
Tighten
Walking Beam Bolts Torque - 330 ft-lb (448 Nm)
Caster Wheel Anti-
Shimmy
Dampener Bolts
Inboard Bolt Torque - 100 ft-lb (135 Nm)
Outboard Bolt Torque - 85 ft-lb (115 Nm)
Drive Wheel Nuts
Torque - 175-200 ft-lb (237-271 Nm)
Repeat Checks Until Torque Stabilizes
Engine Gearbox Oil Change
Drive Wheel Oil Change
50
Hydraulic Oil filters Change
100 Main Gearbox Oil Check
150 Main Gearbox Oil Check
10 Hrs or
Daily
1. Check Tire Inflation
2. Check Engine Oil and Engine Coolant Levels
3. Clean Radiator, Hyd Oil Cooler, Charge Air Cooler, A/C
Condenser
4. Check Hydraulic Oil Level, Hoses and Lines for leaks.
5. Drain Fuel Filter Water Tap
50 Hrs
1. Grease Caster Pivots and Spindle Bearings
2. Grease Walking Beam Center Pivot
3. Grease Top Link Pivots
4. Clean Cab Fresh Air Intake Filter
5. Check Engine Gearbox/Drive Wheel Lube
200 Hrs or
Annually
1. Check Drive Wheel Lubricant Level
2. Grease Formed Caster Wheel Hub Bearings
3. Check Wheel Nut Torque
500 Hrs
1. Change Engine Oil and Filter (or annually)
2. Change Fuel Filters
3. Change Engine Gearbox Lubricant
4. Change Hydraulic Oil Filters
5. Check Engine Valve Tappet Clearance- M200
6. Change Engine Air Cleaner Filter Element- M200
7. Change Crankcase Breather- M200 ONLY
8. Check Safety Systems (or annually)
1000 Hrs
1. Change Engine Air Cleaner Filter Element- M150
2. Change Drive Wheel Lubricant
3. Check Engine Valve Tappet Clearance
2000 Hrs
1. Change Hydraulic Oil
2. Perform General Engine Inspection
3. Change Engine Coolant (M150 ONLY)
3000 Hrs 1. Change Engine Coolant (M200 ONLY)
Annually
1. Change Fuel Tank Vent Line Filter
2. Check Battery Fluid Level & Battery Charge
3. Check Anti-Freeze Concentration
4. Cycle A/C Blower Switch to circulate Refrigerant Oil
Fuel Volume Spec
Sulphur
(by wgt)
Water &
Sediment
(by wgt)
Lubricity
Diesel No.2
97G
(378L)
ASTM
D-975
As per
Spec
As per
Spec
As Per
Spec
1%max
Diesel No.1
& 2 mix
97G
(378L)
n/a
.5% rec.
.1% max
460
HFRR
Fluid Volume Spec Description
ASTM
Anti-freeze
5.3 US G
(20L)
D-4985
Ethylene Glycol Or Propylene-
Glycol With SCA.
A/C
Refrigerant
3.6lbs
(163kg)
R134A Refrigerant
Compressor
Oil
8.1fl.oz
(240cc)
SP-15 Compressor
Lubricant Volume Specification Use
Grease N/A
SAE Multi-
Purpose. High
Temp, Extreme
Pressure EP2.
Max 1%
molybdenum
disulphide.
Lithium base
As required.
CAT
15.8 US
Qt (15L)
SAE 15W40 for
API Class CH-4
& C1-4 Engine
Oil
Engine
Crankcase
Engine
Oil
Cummins
10.6 US
Qt (10L)
SAE 15W40 for
API Class SJ &
CH-4 Engine Oil
Engine
Crankcase
Hydraulic Oil
17.2 US
Gal (66L)
SAE 15W40 for
API Class SJ &
CH-4 Engine Oil
Windrower &
Header Drive
Engine
gearbox
2.2 US Qt
(2.1L)
SAE 75W-90 API
Service Class
GL-5. E Synthetic
Trans Lube
Gear
Lube
Power
Wheels
1.5 US
Qt (1.4L)
SAE 75W-90 API
Service Class
GL-5. E Synthetic
Trans Lube
Power Wheels
and Engine
Gearbox
To Next Page
Need help?
General
