USING YOUR COOKTOP
STAINLESS FINISH COOKTOP SURFACE BURNERS MODELS WITH PIEZO
Due to certain atmospheric conditions Thesurface burner control knob has no IGNITORS
and becauseof oxidationfromthe sur- pre-set position.The flame can be ad- To light the surface burner:
face burnerpilot,the stainless top on justed to any desired height between 1. Pushin and turn the surface burner
yourappliancemay show signsof rust "OFF" and "HI". control knob to the left (counter-
on the underneathside. This is espe- clockwise)to the LITE position.
ciallytrueinareas of highhumidityand If burnerdoesnot igniteor ifthe burner IMPORTANT:Onlylightonesurface
salt airareas, flameshouldgooutduringcooking,turn burnerat a time.
the burneroff.IF GAS HAS ACCUMU-
To helpeliminatethis condition,caution LATEDAND A STRONGGAS ODOR IS
should be taken to make sure that the DETECTED, WAIT 5 MINUTES FOR
underneath side of the maintop is kept THE GAS ODOR TO DISAPPEAR BE-
dry.This is especiallyimportant inareas FORE RELIGHTING THE BURNER.
of high humidity where moisture accu-
mulates. If you detect signs of rust, we Yourappliancewillfeature oneofthefol-
havefound ithelpfultospraytheunder- lowing three types of surface burners.
neath side with a coat of high-heat Follow the instructions that match the
tested rustolium or silicone paint, surface burners on your appliance.
CAUTION: Removetop from appliance Models with surface burner pilots: 2. Immediately rotate the top burner ig-
nitorknobtothe right (clockwise)sev-
and spray in a well vented area. See page 9 for instructions on lighting eral clicks or until the surface burner
Topreventdamagetothe stainless steel the surface burner pilot, lights.The burnershouldlight within4
seconds (approximately 6 clicks or
cooktop, do not use oversized utensil To lightthe surface burner, push in and one full rotation of the ignitor knob).
(1-inch largerthan the burner grate), turnthe control knobto the left (counter-
clockwise) to the "Lite" position. When
the burner lights, adjustthe knobto de-
BURNER GRATES siredflamesize.
Burner grates must be properly in-
stalled.Do notoperateburnerswithout Models without surface burner pi-
a pan onthe grate.The porcelainfinish lots:
may chip withouta pan to absorbthe Lightmatch.Pushinandturnthecontrol
heat. knobto the left (counter-clockwise)to
the "Lite" position and apply lighted
To install grates: matchimmediatelytothe burner.Adjust 3. When the burner lights,adjust the
1. Place grate on cooktop, locating the knobtothe desiredflamesize. surfaceburnercontrolknobtothede-
each of the fourgratelegs on top of siredflame size.
thefour blackplasticgrommets.
If the burner does not lightwithin 4 se-
conds, turn the surface burner knob to
__ the OFF positionand wait 5minutes be-
fore relighting the burner.
To operate the surface burner during a
__ powerfailure or ifthe Piezoignitoris not
functional:
_-Jf_ CAUTION 1. Be sure all controls are in the OFF
Do not turn the control knob on and al- positions.
Iowgasto escape before lightingmatch. 2. Hold a lighted match to the desired
surface burner head.
2. Pressdown at each corner to secure 3. Push in and turn the surface burner
burner grate to cooktop, control knob to the LITE position.
4. When the burner lights, adjust the
surface burnercontrol knobtothe de-
sired flame size.
-8-
To Next Page
Loading...