What to do if Makita EA3200S Chainsaw starts then dies?
If your Makita Chainsaw starts but then immediately dies, the issue might stem from an incorrect idling adjustment or a dirty suction head or carburetor. Adjust the idling and clean these components. Additionally, a defective tank venting system, interrupted fuel line, defective cable, or a faulty combination switch could be the cause. Repair the tank venting and check the fuel line.
Why is my Makita EA3200S having warm start difficulties?
If you're experiencing warm start difficulties with your Makita Chainsaw, it could be due to a wrong carburetor adjustment. Adjust the carburetor correctly to resolve this issue.
How to fix no chain lubrication on a Makita EA3200S?
If there is no chain lubrication in your Makita Chainsaw, it could be due to an empty oil tank, a dirty oil guide groove, or an incorrectly adjusted oil pump screw. Fill the oil tank, clean the oil guide groove, and adjust the oil pump screw to resolve this issue.
Why is my Makita EA3200S engine not starting?
If your Makita Chainsaw engine won't start or is difficult to start, it could be due to a malfunction in the fuel supply system, compression system, or a mechanical issue. Other potential causes include the STOP switch being in the wrong position, a fault or short-circuit in the wiring, a defective spark plug cap or spark plug, the combination switch being in the Choke position, a defective carburetor, a dirty suction head, a bent or interrupted fuel line, a defective cylinder base packing ring or radial shaft packings, defective cylinder or piston rings, a spark plug that doesn't seal, a broken spring in the starter, or broken parts inside the engine. To resolve this, identify and rectify the faulty system(s), including fuel supply, compression, or wiring issues.
What to do if my Makita EA3200S Chainsaw engine does not start?
If your Makita Chainsaw engine is not starting, it could be due to a malfunction in the fuel supply system, compression system, or a mechanical issue. Inspect and repair the fuel supply system and check for compression problems. Also, make sure the STOP switch is in the correct position, check for any wiring faults or short circuits, and inspect the spark plug cap or spark plug for any defects.
Why is my Makita Chainsaw chain not getting lubrication?
If your Makita Chainsaw chain isn't getting lubrication, it could be due to an empty oil tank, a dirty oil guide groove, or an incorrectly adjusted oil pump. Fill the oil tank, clean the oil guide groove, and adjust the oil pump.
How to fix warm start difficulties with Makita Chainsaw?
Warm start difficulties with your Makita Chainsaw is caused by a wrong carburetor adjustment. Adjust the carburetor settings to resolve this issue.
What to do if Makita EA3200S engine starts, but dies immediately?
If your Makita Chainsaw engine starts and then dies immediately, it could be due to: * Incorrect idling adjustment, or a dirty suction head or carburetor. Suggested solution: Correct the idling adjustment and clean the carburetor. * Defective tank venting, an interrupted fuel line, a defective cable, or a defective combination switch. Suggested solution: Fix the tank venting and inspect the fuel line.
What to do if Makita EA3200S Chainsaw has insufficient power?
If your Makita Chainsaw has insufficient power, it might be because: * The air filter is dirty. * The carburetor adjustment is incorrect. * The muffler is clogged. * The exhaust channel in the cylinder is clogged. * The spark arrester screen is clogged. To resolve this, clean or replace the air filter and check the carburetor settings.
Why is my Makita EA3200S Chainsaw not lubricating the chain?
If there is no chain lubrication in your Makita Chainsaw, it could be because the oil tank is empty, the oil guide groove is dirty, or the oil-pump adjusting screw is incorrectly adjusted. Fill the oil tank, clean the oil guide groove, and adjust the oil-pump adjusting screw.
General| Weight | 4.1 kg |
|---|---|
| Chain Pitch | 3/8" |
| Power Output | 1.35 kW |
| Bar Length | 35 cm |
| Fuel Tank Capacity | 0.4 L |
| Chain Gauge | 0.050" |
| Oil Tank Capacity | 0.28 L |
To Next Page
