What to do if the cutting blade does not move on a Makita Trimmer?
If the cutting blade of your Makita Trimmer isn't moving, it could be due to loosened cutting blades or the tightening nut; ensure they are tightened securely. Another possibility is that twigs or other foreign matter are caught in the cutting blades; remove any obstructions.
Why is my Makita Trimmer main unit vibrating abnormally?
If your Makita Trimmer unit is vibrating abnormally, it could be due to broken, bent, or worn cutting blades, which would require replacement. Alternatively, the cutting blades or tightening nut might be loose, so make sure to tighten them securely.
Why is my Makita Trimmer vibrating abnormally?
Abnormal vibration in your Makita Trimmer can be caused by: * Broken, bent, or worn cutting blades. Replace the cutting blades. * Loosened cutting blades-tightening nut. Tighten the nut securely.
What to do if the cutting blade on my Makita EN5950SH does not move?
If the cutting blade on your Makita Trimmer does not move, check if: * The cutting blades-tightening nut is loosened. Tighten it securely. * Twigs are caught by the cutting blades. Remove any foreign matter.
How to fix Makita EN5950SH Trimmer when engine does not start?
If your Makita Trimmer engine won't start, try these steps: First, push the primer pump 7 to 10 times. Then, pull the starter rope strongly. Ensure the trimmer has fuel and that the fuel filter isn't clogged—clean it if it is. Also, check for a broken or deteriorated fuel tube and straighten or replace it. Replace deteriorated fuel, as it makes starting difficult (recommended replacement is every 1 month). Check that the plug cap is securely attached and the spark plug is clean with proper clearance; clean or adjust as needed. If the issue persists, there may be an abnormal carburetor, drive system, or starter rope, requiring professional inspection.
What to do if cutting blades do not stop immediately on Makita EN5950SH Trimmer?
If the cutting blades of your Makita Trimmer don't stop immediately, it could be due to high idling rotation. Try adjusting it. Alternatively, the throttle wire might be detached; ensure it's securely attached.
Why does my Makita EN5950SH engine stop soon or not increase speed?
Your Makita Trimmer's engine might stop soon after starting or fail to reach full speed due to several reasons. Make sure you perform a proper warm-up operation. Check that the choke lever isn't set to the closed position when the engine is warm. A clogged fuel filter or a contaminated air cleaner can also cause these issues; clean or replace them as necessary. For abnormal carburetor or drive system issues, it's best to request professional inspection and maintenance.
What to do if my Makita Trimmer engine does not stop?
If your Makita Trimmer engine won't stop, check if the connector is detached and attach it securely. If the electric system is abnormal, it is best to request inspection and maintenance.
What to do if my Makita EN5950SH Trimmer engine stops soon and the speed doesn't increase?
If your Makita Trimmer's engine stops soon after starting or the engine speed does not increase, consider the following possibilities: * The engine might not be sufficiently warmed up. Perform the warm-up operation. * The choke lever may be set incorrectly. Ensure it is set to the correct position once the engine is warmed up. * The fuel filter could be clogged. Clean or replace it. * The air cleaner might be contaminated or clogged. Clean it.
How to fix Makita Trimmer cutting blades that won't stop immediately?
If the cutting blades on your Makita Trimmer do not stop immediately, it could be due to: * High idling rotation. Adjust the idling rotation. * A detached throttle wire. Attach the throttle wire securely.
Details required protective gear like helmets, eye/ear protection, gloves, and shoes.
Maintain distance from electric lines, ensure ventilation, and keep bystanders away.
Loosen tank cap, refuel with engine off, wipe periphery, tighten cap.
Loosen tank cap, refuel with engine off, wipe periphery, tighten cap securely.
Ensure safe condition, check blades, handles, and stop switch before starting.
Set machine on flat space, move I-O switch to OPERATION, push primer pump.
Pull start knob gently to compression, then pull strongly. Do not release suddenly.
Repeat primer pump, keep throttle at idle, pull recoil starter.
Adjust blade clearance using the truss bolt and nut to ensure a clean cut without overheating.
Check for loose parts, air passages, clean air filter, check blades after use.
Drain old oil, replace gasket and drain bolt, refill with new oil to the upper limit mark.
Clean air cleaner daily or every 10 hours. Remove elements, tap dirt, wash if heavily contaminated, dry completely.
Clean fuel filter monthly or every 50 hours. Check for debris, clean or replace if clogged.
Drain fuel from tank and carburetor, run engine dry, add oil to spark plug hole, attach blade cover.
To Next Page
General
