Makita ER2550LH User Manual (English)

Other manuals for Makita ER2550LH

Questions and Answers:

L
Lisa WestAug 21, 2025
Why does my Makita Trimmer engine stop soon after starting?
- C
  Craig CooperAug 21, 2025
  If your Makita Trimmer engine stops soon after starting, it might not be warmed up properly; perform the warm-up operation. Also, ensure the choke lever is set to “OPEN” once the engine is warm. Check and clean the fuel filter and air cleaner for any clogs or contamination. If the problem continues, the carburetor or drive system may be abnormal, requiring professional inspection and maintenance.
S
Stephen RussellAug 23, 2025
What causes the nylon cutting cord to not feed on my Makita Trimmer?
- M
  Mrs. Katherine SnowAug 23, 2025
  If the nylon cutting cord on your Makita Trimmer does not feed, it might be because the cord is used up or tangled in the spool. Rewind the cord to resolve this.
R
richardjacksonAug 26, 2025
How to fix a Makita ER2550LH when the nylon cutting cord does not feed?
- J
  Joseph King DDSAug 26, 2025
  If the nylon cutting cord on your Makita Trimmer does not feed, it might be used up or tangled in the spool. Rewind the cord.
H
hicksnathanAug 27, 2025
How to troubleshoot starting issues with my Makita ER2550LH Trimmer?
- R
  Randall GutierrezAug 27, 2025
  If your Makita Trimmer's engine won't start, try these steps: Ensure you've pushed the primer pump 7 to 10 times. Pull the starter rope strongly. Make sure there's enough fuel in the tank. Check for and clean any clogs in the fuel filter. Straighten any broken fuel tubes and replace deteriorated fuel, ideally monthly. If there's excessive fuel suction, adjust the throttle lever from medium to high speed and pull the starter handle. Also, check that the plug cap is securely attached and that the spark plug is clean and properly gapped. If problems persist, the carburetor, starter rope, or drive system might be abnormal, requiring professional inspection.
S
suelloydAug 29, 2025
Why is the nylon cutting cord on my Makita ER2550LH not cut off at the correct length?
- R
  Richard Leblanc DDSAug 30, 2025
  If the nylon cutting cord on your Makita Trimmer isn't being cut off at the correct length, rewind the cord if it extends past the protector. If the cord cutter on the protector is damaged or missing, ask Makita authorized service center to replace it.
C
corygriffinSep 1, 2025
Why is the nylon cutting cord not cut off at the correct length on my Makita ER2550LH?
- J
  jason30Sep 1, 2025
  If the nylon cutting cord on your Makita Trimmer is not cut off at the correct length, it could be due to a damaged or missing cord cutter on the protector. In this case, ask a Makita authorized service center to replace the cord cutter. Alternatively, the cord may extend past the protector, in which case you should rewind it.
S
Sean NorrisSep 3, 2025
What to do if my Makita Trimmer engine stops soon after starting?
- D
  Douglas FloresSep 3, 2025
  If your Makita Trimmer engine stops soon after starting, consider the following: * The engine might not be sufficiently warmed up. Perform a warm-up operation. * The choke lever might be set to 'CLOSE' even after the engine is warmed up. Set it to 'OPEN'. * The fuel filter may be clogged. Clean it. * The air cleaner could be contaminated or clogged. Clean it.
A
Anna WestSep 5, 2025
What to do if my Makita ER2550LH Trimmer engine does not stop?
- B
  Brianna RodriguezSep 5, 2025
  If your Makita Trimmer engine does not stop, check if the connector is detached and attach it securely.
D
Derrick VasquezSep 7, 2025
Why is my Makita Trimmer vibrating abnormally?
- J
  James JacksonSep 7, 2025
  Abnormal vibration in your Makita Trimmer can be due to: * A broken cutting attachment. Replace it with a new one. * The cutting attachment not being tightened securely. Tighten it securely. * One end of the nylon cutting cord being broken, causing the nylon cutting head to become unbalanced. Feed the nylon cutting cord by tapping the nylon cutting head on the ground.
C
Carl SuttonSep 9, 2025
What to do if the cutting attachment on my Makita ER2550LH Trimmer does not rotate?
- Z
  zperezSep 10, 2025
  If the cutting attachment on your Makita Trimmer isn't rotating, it could be due to: * The cutting attachment not being tightened securely. Tighten it securely. * A twig caught between the cutting attachment and the protector. Remove the foreign matter.