Manitou MC 18-2 D K ST3A S1 - Page 63

3 - 7
Âo
1000H - ROUTINE MAINTENANCE - EVERY 1000 HOURS OF SERVICE OR 2 YEARS
ALSO PERFORM THE 500 HOUR PERIODIC MAINTENANCE OPERATIONS.
- CHECK Safety belt....................................................................... 3-24
- CLEAN Fuel tank ........................................................................ 3-24
- REPLACE Dry air filter cartridge ............................................................ 3-24
- REPLACE Hydraulic oil ..................................................................... 3-25
- REPLACE Hydraulic oil tank filter cap....................................................... 3-25
- CHECK Engine silent blocks * ............................................................ 3-26
- CHECK Engine speeds * ................................................................. 3-26
- CHECK Engine valve clearances * ........................................................ 3-26
- CHECK Condition of wheels and tyres * .................................................. 3-26
- CHECK Speeds of hydraulic movements * ................................................ 3-26
- CHECK Condition of hoses and flexible pipes * ........................................... 3-26
- CHECK Condition of cylinders (leakage, rods) * ........................................... 3-26
- CHECK Condition of wiring harnesses and cables * ....................................... 3-26
- CHECK Lights and signals (option) * ..................................................... 3-26
- CHECK Warning indicators * ............................................................. 3-26
- CHECK Condition of the rear view mirrors * .............................................. 3-26
- CHECK Cab structure * .................................................................. 3-26
- CHECK Frame structure * ................................................................ 3-26
- CHECK Attachment carriage * ........................................................... 3-26
- CHECK Condition of attachments * ...................................................... 3-26
* Consult your dealer.
Âp
2000H - PERIODIC MAINTENANCE - EVERY 2000 HOURS OF SERVICE OR 4 YEARS
ALSO PERFORM THE 500 HOUR AND 1000 HOUR PERIODIC MAINTENANCE OPERATIONS.
- CHECK Wheel nut tightening torques.................................................... 3-28
- REPLACE Dry air filter safety cartridge...................................................... 3-28
- REPLACE Coolant ......................................................................... 3-28
- CHECK Injection pump * ................................................................ 3-29
- CHECK Injectors * ....................................................................... 3-29
- CHECK Radiator * ....................................................................... 3-29
- CHECK Water pump and thermostat * ................................................... 3-29
- CHECK Alternator and starter * .......................................................... 3-29
- CHECK Hydrostatic transmission circuit pressures *....................................... 3-29
- CHECK Hydrostatic transmission control flow *........................................... 3-29
- CHECK Hydrostatic transmission / accelerator cut-off operation * ......................... 3-29
- CHECK Steering * ....................................................................... 3-30
- CHECK Swivel pins (MC 18-2) ............................................................ 3-30
- CHECK Wheel reduction gear pivots (MC 18-4) ........................................... 3-30
- CHECK Rear axle *....................................................................... 3-30
- CHECK Disc brake wear on wheel motors *............................................... 3-30
- CHECK Condition of boom assembly * ................................................... 3-30
- CHECK Mast lifting chains *.............................................................. 3-30
- CHECK Mast lifting chain pulleys * ....................................................... 3-30
- CHECK Mast guide rollers * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
- CHECK Mast bearing rollers * ............................................................ 3-30
- CHECK Thickness of the mast wearing plates * ........................................... 3-30
- CHECK Hydraulic circuit pressures *...................................................... 3-30
- CHECK Hydraulic circuit flow rates * ..................................................... 3-30
- CHECK Bearings and bushings * ......................................................... 3-30
- CLEAN/CHECK Hydraulic oil tank and strainer *
.................................................. 3-30
* Consult your dealer.
647635 (12/12/2017)
M
C 18-2 / MC 18-4 ST3A S1
www.duma-rent.com