What does it mean if the power indicator is blinking red after turning on my Marantz NR1402 Receiver?
This unit amplifier circuit has failed. Turn off the power and please contact the marantz service adviser.
Why is the power indicator blinking red on my Marantz NR1402?
If the power indicator on your Marantz Receiver is blinking red approximately every 0.5 seconds, ensure you are using speakers with the specified impedance. Also, check the speaker cables for any shorts (touching wires). Firmly twist the core wire in the speaker cable, and then reconnect it to the speaker terminal.
Why is there no sound from my Marantz NR1402 Receiver subwoofer?
If there's no sound from the subwoofer connected to your Marantz Receiver, check the subwoofer connections and ensure the subwoofer is powered on. In the receiver's menu, set “Speaker Config.” – “Subwoofer” to “Yes”. Also, if “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
Why is there no sound from surround speakers on my Marantz Receiver?
If there's no sound coming from the surround speakers connected to your Marantz Receiver, verify that the surround speakers are connected to the SURROUND terminals.
Why is there no sound from the surround back speaker on my Marantz Receiver?
If you're not getting sound from the surround back speaker on your Marantz Receiver, check if “Pre Assign” is set appropriately to output audio from the surround back speakers. Also, set “Speaker Config.” – “S.Back” on the menu to something other than “None”. Ensure the surround mode is set to something other than “STEREO” and “VIRTUAL”.
How to enable DTS sound output on a Marantz NR1402 Receiver?
If DTS sound is not output from your Marantz Receiver, set “Decode Mode” on the menu to “Auto” or “DTS”.
Why can't Dynamic EQ and Dynamic Volume be selected on my Marantz NR1402?
If Dynamic EQ® and Dynamic Volume® cannot be selected on your Marantz Receiver, run Audyssey® Auto Setup.
How to turn on the display on a Marantz NR1402?
If the display on your Marantz Receiver is off, set “Display” on the menu to something other than “OFF”.
How do I disable HDMI control on my Marantz NR1402?
If operations on HDMI-connected devices are mirrored on your Marantz Receiver, set “HDMI Control” in the menu to “OFF”. If you wish to prevent power off operations from linking with HDMI control-compatible devices, set “P.Off Control” in the menu to “OFF”.
How can I improve radio reception on my Marantz Receiver?
If you're experiencing poor reception, noise, or distortion with your Marantz Receiver, try these steps: * Change the antenna orientation or position. * Separate the AM loop antenna from the unit. * Use an FM outdoor antenna. * Separate the antenna from other connection cables.
Key safety guidelines for operation and maintenance.
Legal compliance statement and product disposal guidelines.
Lists and illustrates the product's included accessories.
Highlights key functions and capabilities of the AV receiver.
Provides important safety and handling advice for the unit.
Explains how to connect various devices to the unit.
Guides users through the unit's configuration settings.
Details how to operate the unit for basic playback.
Explains how to choose different sound modes.
Instructions for connecting devices via HDMI and its functions.
Connecting DVI-D devices and HDMI configuration options.
Guides for connecting TVs, disc players, and CD players.
Guides for set-top boxes, audio players, and wireless receivers.
Detailed guide for automatic speaker setup.
Basic playback operations and sound mode selection.
Steps for microphone, subwoofer, and remote configuration.
Details the measurement and calculation phases of auto setup.
Reviewing, saving, and finalizing the auto setup process.
Explains common error messages and solutions during setup.
Reviewing measurement results and equalizer settings.
How to choose audio/video input.
Controls for volume, muting, and playing devices.
How to select radio stations and sound modes.
Steps for tuning radio stations and saving presets.
Using RDS, PTY, TP, and RT for radio reception.
Using buttons to choose sound modes.
Explains various Dolby, DTS, and Marantz sound modes.
Advanced methods for speaker setup and wiring.
Advanced connectivity options and playback functions.
Guide to detailed system configurations and setup.
Example setups for 7.1 channel surround sound.
Example setups for 6.1 and 2.1 channel sound.
Configuring speaker connections and active channels.
Linking marantz components for remote control.
Linking HDMI devices for integrated control.
Setting auto-off timer and managing settings backups.
Unit lock, and other convenient features.
Overview of menu structure and text entry methods.
Options for fine-tuning audio parameters.
Manual speaker configuration and assignment.
Configuring HDMI video and audio output.
Settings for audio playback preferences.
Accessing various other system settings.
Setting the user interface language.
Setting speaker volume levels and bass cut-off frequencies.
Configuring standby source and power-off linking.
Features for audio sync and device linking.
Settings for radio station presets (Auto, Skip, Name).
Assigning HDMI, Digital, Component connectors to sources.
Configuring video sources and audio input/decode modes.
Customizing input names and adjusting audio levels.
Disabling/enabling the unit's remote sensor.
Setting up the remote for other manufacturers' devices.
Using the remote to control connected AV equipment.
Identification of unit components.
Solutions for common operational problems.
Technical details and measurements of the unit.
Alphabetical lookup and remote programming codes.
Identifies all rear panel input/output connectors.
Explains functions of all remote control buttons.
Guide for battery installation and care.
Overview of modes, speaker use, and parameter adjustability.
Cross-reference of input signals to compatible surround modes.
Definitions of audio formats and technologies.
Definitions of technical terms like HDCP, HDMI, LFE.
Common issues and solutions for the unit and HDMI.
Solutions for video, audio, and radio reception problems.
Solutions for M-XPort, remote issues, and microprocessor reset.
Details on amplifier power, audio output, and tuner specs.
Video connector specs and power details.
Codes for programming remote controls for various devices.
Codes for programming remote controls for CD players.
Physical measurements and weight of the AV receiver.
Key safety guidelines for operation and maintenance.
Legal compliance statement and product disposal guidelines.
Lists and illustrates the product's included accessories.
Highlights key functions and capabilities of the AV receiver.
Provides important safety and handling advice for the unit.
Explains how to connect various devices to the unit.
Guides users through the unit's configuration settings.
Details how to operate the unit for basic playback.
Explains how to choose different sound modes.
Instructions for connecting devices via HDMI and its functions.
Connecting DVI-D devices and HDMI configuration options.
Guides for connecting TVs, disc players, and CD players.
Guides for set-top boxes, audio players, and wireless receivers.
Detailed guide for automatic speaker setup.
Basic playback operations and sound mode selection.
Steps for microphone, subwoofer, and remote configuration.
Details the measurement and calculation phases of auto setup.
Reviewing, saving, and finalizing the auto setup process.
Explains common error messages and solutions during setup.
Reviewing measurement results and equalizer settings.
How to choose audio/video input.
Controls for volume, muting, and playing devices.
How to select radio stations and sound modes.
Steps for tuning radio stations and saving presets.
Using RDS, PTY, TP, and RT for radio reception.
Using buttons to choose sound modes.
Explains various Dolby, DTS, and Marantz sound modes.
Advanced methods for speaker setup and wiring.
Advanced connectivity options and playback functions.
Guide to detailed system configurations and setup.
Example setups for 7.1 channel surround sound.
Example setups for 6.1 and 2.1 channel sound.
Configuring speaker connections and active channels.
Linking marantz components for remote control.
Linking HDMI devices for integrated control.
Setting auto-off timer and managing settings backups.
Unit lock, and other convenient features.
Overview of menu structure and text entry methods.
Options for fine-tuning audio parameters.
Manual speaker configuration and assignment.
Configuring HDMI video and audio output.
Settings for audio playback preferences.
Accessing various other system settings.
Setting the user interface language.
Setting speaker volume levels and bass cut-off frequencies.
Configuring standby source and power-off linking.
Features for audio sync and device linking.
Settings for radio station presets (Auto, Skip, Name).
Assigning HDMI, Digital, Component connectors to sources.
Configuring video sources and audio input/decode modes.
Customizing input names and adjusting audio levels.
Disabling/enabling the unit's remote sensor.
Setting up the remote for other manufacturers' devices.
Using the remote to control connected AV equipment.
Identification of unit components.
Solutions for common operational problems.
Technical details and measurements of the unit.
Alphabetical lookup and remote programming codes.
Identifies all rear panel input/output connectors.
Explains functions of all remote control buttons.
Guide for battery installation and care.
Overview of modes, speaker use, and parameter adjustability.
Cross-reference of input signals to compatible surround modes.
Definitions of audio formats and technologies.
Definitions of technical terms like HDCP, HDMI, LFE.
Common issues and solutions for the unit and HDMI.
Solutions for video, audio, and radio reception problems.
Solutions for M-XPort, remote issues, and microprocessor reset.
Details on amplifier power, audio output, and tuner specs.
Video connector specs and power details.
Codes for programming remote controls for various devices.
Codes for programming remote controls for CD players.
Physical measurements and weight of the AV receiver.
General| Frequency range | 8 - 100000 Hz |
|---|---|
| Audio output channels | 5.1 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Power output per channel (20-20KHz@8 Ohm) | 50 W |
| HDMI in | 4 |
| AC (power) in | Yes |
| Composite video in | 3 |
| Digital audio optical in | 1 |
| Multichannel audio input type | Terminals |
| Component video (YPbPr/YCbCr) in | 2 |
| Headphone connectivity | 3.5 mm |
| Connectivity technology | Wired |
| Speakers connectivity type | Clamp terminals |
| Ethernet LAN | No |
| AM band range | 530 - 1710 kHz |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | AM, FM |
| Display | LCD |
| HDMI version | 1.4 |
| Product color | Black |
| Audio decoders | Dolby TrueHD, DTS-HD |
| Volume control | Rotary |
| Apple docking compatibility | Not supported |
| Power consumption (standby) | 0.2 W |
| Power consumption (typical) | 180 W |
Weight and Dimensions| Depth | 367 mm |
|---|---|
| Width | 440 mm |
| Height | 105 mm |
| Weight | 8200 g |
To Next Page
