3
2.2 LED Check
1) Press the REC PAUSE button and REC LEVEL – button
at the same time, and turn the POWER slide switch ON.
At this time, the service menu list is displayed in the
display section.
2) Press the VOL + and VOL – buttons to select “LED Check”.
At this time, the selected menu item is highlighted.
3) If the 3/8/ENTER button is pressed, “∗” is displayed on
the back of “LED Check”, and all LEDs light (REC, OVER,
LEVEL, REMOTE RED, REMOTE GREEN).
• If the
4
button is pressed while all LEDs are lit, all
LEDs go off, and the display returns to the service
menu list.
• If the
3
/
8
/
ENTER
button is pressed while all LEDs
are lit, all LEDs go off, the “
∗
” display switches off, and
the display returns to the service menu list.
2.3 Door Sence
1) Press the REC PAUSE button and REC LEVEL – button
at the same time, and turn the POWER slide switch ON.
At this time, the service menu list is displayed in the
display section.
2) Press the VOL + and VOL – buttons to select “Door Sence”.
At this time, the selected menu item is highlighted.
3) If the 3/8/ENTER button is pressed, the PMD620 sensor
is set to OFF.
• At this time, “Executing…” is displayed in the display
section.
• If the settings are completed, “Completed” is
displayed in the display section for 1 second, the
display returns to the service menu and “Door Sense
OFF” is displayed.
If the 3/8/ENTER button is pressed while “Door Sense
OFF” is displayed, the PMD620 sensor is set to ON.
2.2 LED チェック
1)
REC PAUSE
ボタンと
REC LEVEL −
ボタンを同 時に
押しながら、
POWER slide
スイッチを Onします。この
とき、表示部にサービスメニュー一覧が表示されます。
2)
VOL +
ボタンおよび
VOL –
ボタンを押して、“LED
Check” を選択します。このとき、選択したメニューが
ハイライト表示されます。
3)
3
/
8
/
ENTER
ボタンを押すと、メニューの“LED Check”
の後ろに“∗”が表示され、LED が全点灯(REC、 OVER、
LEVEL、 REMOTE RED、 REMOTE GREEN)します。
•
LEDが全点灯中に
4
ボタンを押すと、LEDを全消灯
させ、サービスメニュー一覧に戻ります。
•
LEDが全点灯中に
3
/
8
/
ENTER
ボタンを押すと、LED
を全消灯させ、“∗” 表示を消灯しサービスメニュー一覧
に戻ります。
2.3 ドアセンサの設定
1)
REC PAUSE
ボタンと
REC LEVEL −
ボタンを同 時に
押しながら、
POWER slide
スイッチを Onします。この
とき、表示部にサービスメニュー一覧が表示されます。
2)
VOL +
ボタンおよび
VOL –
ボタンを押して、“Door Sense
ON” を選択します。このとき、選択したメニューがハイ
ライト表示されます。
3)
3
/
8
/
ENTER
ボタンを押すと、PMD620 をセンサOFF
状態に設定します。
•
このとき、表示部に“Executing...”が表示されます。
•
設定が完 了すると、表示 部に“Completed”が1秒間
表示され、サービスメニューに戻り “Door Sense OFF”
が表示されます。
“Door Sense OFF” 表 示しているときに
3
/
8
/
ENTER
ボタンを押すと、PMD620をセンサON状態に設定します。