Marantz SR1041 - TUNER OPERATION AND MEMORY; Preset Memory Operations; Preset Scan Tuning

TUNER OPERATION
The number of controls and buttons on the main unit are enclosed in
©, and those on the remote control are enclosed in [7].
Before proceeding to tuner operation, press the FM/AM function button
of the remote control to set the remote control in the tuner mode.
e To listen to the tuner
1. Set the VOLUME contro! @ to the minimum position.
2. Press the POWER switch (6/[1] to turn the power ON.
3. Press the FM/AM button @ or the FM/AM function button [2] to
select the radio band to be received.
. Press the F/P button @ to select the frequency display.
5. Press the & UP or ¥ DOWN button @/{5] to scan the frequency.
Pressing the button for less than 0.5 second scans the frequency
by 1 step. Holding the button depressed scans the frequency
continuously. When the button is released in this mode, auto
tuning starts. Auto tuning stops automatically when a broadcasting
station is tuned into, and the TUNED indicator lights up.
6. Adjust the volume with the VOLUME contro! @/114).
The following operation is available only on the remote control.
When receiving the FM band, set the desired audio mode with the
MODE button 49/[1.
When the AUTO indicator is lit up:
When a stereo programme is being received, the STEREO
indicator lights up and the programme is received in stereo.
To receive sound in mono, press the MODE button so that the
AUTO indicator goes off.
h
PRESET MEMORY OPERATION
This unit can store up to 30 stations selected randomly in the FM,
MW and LW bands.
The preset memory function allows the frequency, receiving mode
and also the station name to be stored in the memory.
The preset memory can be jilled in two ways:
e Manual preset memory
1. Select a desired station, referring to “Tuner Operation”.
2. Press the PROG button (13).
The MEMO indicator will blink for approx. 5 seconds. In this
period, select the preset number with one of the following
procedures.
* Select the preset number with the UP or DOWN button and
press the MEMO/ST.N button @.
* Select the preset number by directly entering it with the numeric
buttons. (Remote control only)
Note:
It is recommended that numbers from 1 to 3 be entered as two digits,
e.g. 01 to 03. They can also be entered as one digit, but a waiting
period of 1.5 seconds is required in this case.
e Auto preset memory (main unit only)
This allows a band to be scanned automatically, a station with good
reoperation to be found and to be and stored in the preset memory.
1. Select the desired band and frequency.
2. While holding the MEMO/ST.N button @ depressed, press the A
UP button @). The auto preset memory operation starts.
Starts auto scanning within the band.
3. The MEMO indicator flashes on the display.
4. When a station is received, scanning pauses for 5 seconds. In
this period, the following operations can be performed.
1) Changing the band @.
2) Changing the mode @.
5. If no button is pressed in the period above, the frequency being
received is stored. If the & UP button @ is pressed in the 5-
second period, scanning restarts without storing the frequency
being received in the memory.
6. When stations up to [P30] have been preset, auto preset memory
iS automatically stopped.
To stop in mid-operation, press one of the function buttons @ or,
on the remote control, press one of the function buttons [2] or the
O/CL button 7.
e Station name preset
The station name preset function allows the name of each preset
channel to be entered using alphanumeric characters.
The Station Name button is valid only in the tuner mode and the
preset number display mode.
Before station name preset operation, store stations with the preset
memory operation described on the previous page.
1. Press and hold the MEMO/ST.N button for more than 3 seconds.
2. The leftmost column of the station name indicator flashed,
indicating the character entry ready status.
[ Operation using the buttons on the main unit ]
3. When the & UP button @ is pressed, alphabetic and numeric
characters will be displayed in the following order:
A>B>C...2Z> 1 > 233...0 > - _(Blank) 3A
UP >
<— DOWN
Holding the button depressed displays alphanumeric characters
at high speed, and pressing the W DOWN button reverses the
order.
4. After selecting the first character to be entered, press the
MEMO/ST.N button @. The entry in this column is fixed and the next
column starts to flash. Fill the next column and press the
MEMO/ST.N button @ for more than 1 second to confirm the entry.
Note:
Unused columns should be filled by entering blanks.
[ Operation using the buttons on the remote control ]
3. Enter the character using the numeric buttons [3] [4].
For example, to enter “A”:
1) Press the “1” button. “A” appears on the display column.
2) Every time the “1” button is pressed, the displayed character
changes in the order: A> BC 31-4...
Pressing buttons other than the “1” button cause different
characters to be displayed in a similar way, so that other
alphanumeric characters can be entered.
To enter a blank or space, press the “9” button.
4. When the desired character is displayed, press the PROG button
to confirm the entry in this column and move to the next
column.
After having filled all of the 5 columns, press the PROG button
for more than 1 second again.
Recalling a station from the preset memory (remote
control only)
1. Direct selection by pressing numeric buttons [3] [4):
Enter an integer from 1 to 30. 1-digit preset numbers 1 to 9 should
be preceded by 0, for example “05”. The entry is complete when
the second digit has been entered.
2. Selection using + or — buttons [10]
Each press of the + or — button [10] increases or decreases the
preset number by one, holding the button depressed changes the
preset numbers at a high speed and releasing the button stops
the high-speed change.
e Preset scan tuning
1. Press the P-SCAN button @).
The P-SCAN indicator flashes on the display, and the display
enters the preset number display mode. (The smallest preset
number is recalled at this time. If no station has been preset,
“POO” flashes and the display returns to the previous contents.)
2. Preset scan starts endlessly advancing to the next preset number,
for example from P1 to P2, every 5 seconds. The preset numbers
which do not correspond to any preset memory are skipped.
3. Preset scanning can be agcelerated by holding the UP or DOWN
@, “+"or “—" [Id] button depressed.
Preset scanning can be cancelled by pressing the P-SCAN @,
button.
it can also be cancelled by pressing the O button [4].
e Clearing the preset memory (remote control only)
The preset memory contents can be cleared with the following
procedure.
1. Recall the preset number to be cleared with the + or — button (10).
2. Press the PROG button [13] and, while the MEMO indicator flashes
for 5 seconds, press the “O/CL” button [4]. The CLEAR indicator is
displayed and the contents of that preset number are cleared.