Marantz SR1041 - SLEEP TIMER AND TROUBLESHOOTING; Sleep Timer Operation; TROUBLESHOOTING COMMON ISSUES; CARE AND MAINTENANCE

After selecting “ONCE” or “DAILY”, press the MEMO/ST.N button
@.
The ONCE or DAILY operation is set automatically in 8 seconds
even if the MEMO/ST.N button is not pressed.
e The set timer programs can be cancelled temporarily
when they are not required.
1. If the timer indicator is displayed, press the TIMER button @.
When the timer program contents start to be displayed, press the
TIMER button again.
2. The TIMER indicator disappears from the display, and the timer
program will not be executed.
The timer program can be re-activated by pressing the TIMER
button @ again to display the TIMER indicator.
* If both PRG-1 and PRG-2 have been set, it is not possible to
temporarily cancel only one of them.
Checking Timer Program Contents
Use the following procedure to check the timer program contents.
The check is possible even when the power of the unit is OFF.
* 4, Press the TIMER button @. if no timer program has been set, The
TIMER indicator flashes for 2 seconds and then disappears. If any
timer programs have been set, their contents are displayed in the
following order, taking 2 seconds for each step.
2. “TIMER PRG-1" is displayed.
3. “13:50 ON" or “1:50 PM"
(an example of ON time display)
4. “16:30 OFF’ or “4:30 PM”
(an example of OFF time display)
“CD 11” (example when CD track No.11 is to be played)
“DAILY” or “ONCE” (depending whether PRG-1 is DAILY or ONCE)
“TIMER PRG-2” (not displayed when PRG-2 has not been set
The information on PRG-2 is displayed in the same way as in 3 to
6 above.
9. The display returns to the previous display of clock or function.
DNOn
Sleep Timer Setting (remote control only)
The sleep timer function allows the power of the unit to be turned OFF
automatically after a specified period of time.
1. While the power is ON, press the SLEEP button [9].
2. The display shows "SLEEP 10° for 5 seconds (with "10" blinking).
3. Press the SLEEP button in less than 5 seconds. Each press
changes the sleep timer period in order of 10 — 20 + 30 40
50 > 60 > 90 > 120 > -- (OFF) > 10...
4. When the desired period is displayed, leave the controls for 5
seconds; "SLEEP" will light indicating the completion of set-up and
at the same time the sleep timer will start the count.
Press the SLEEP button [9] during counting of sleep timer to
display the remaining period until the power is turned OFF.
To change the set-up period after the sleep timer has started the
count, display the remaining time, press and hold the SLEEP
button [9] for more than 1 seconds while the remaining period is
displayed, and repeat steps 2 to 4 above.
e Tocancel the sleep timer operation, use the following procedure.
A. Press the SLEEP button [9] then, within 5 seconds, press the
“O/CL” numeric button [4]. This cancels the sleep timer.
TROUBLESHOOTING
Should faults occur, it is in many cases not necessary to consult your
dealer or Marantz technical service department. On the basis of the
following checks you will be able to rectify a number of faults yourself
without difficulty.
if the fault cannot be remedied after the following checks, please
consult your dealer or nearest Marantz service agent.
Does sound come from only one side?
— ls the balance control set correctly?
— Check the connections of the loudspeaker which is not working.
—— Check the connections between the sound source and receiver.
— If using headphones, check that the plug is properly inserted into
the jack.
11
Does
the
receiver
hum,
buzz
or
howl
during
recording
or
playback?
— Check the earth (GND) connection of the record player.
+
Are
the
connection
plugs
pushed
far
enough
into
the
jacks?
—
Keep
the
connection
cable
to
the
record
player
as
far
away
as
possible
from
the
mains
power
cable
(in
case
of
hum)
or
TV
circuits
(in
case
of
buzz).
—
The
receiver
may
how!
as
a
result
of
acoustic
feedback
from
the
loudspeakers
to
the
record
player.
This
occurs
mainly
at
higher
volumes.
In this case change the positioning of the loudspeakers.
ENGLISH
You
cannot
hear
anything,
and
no
indicator
lights
up?
—
The
receiver
is
not
switched
on
—
The
receiver
is
not
connected
to
a
mains
power
outlet.
— The mains power outlet is not live.
You
cannot
hear
anything,
but
an
indicator
lights
up?
—
Are
the
function
buttons
in
the
correct
position?
— {ts the selected sound source functioning properly?
— Is the volume control high enough?
Do not keep it in the maximum position!
— Are the loudspeakers connected properly?
Before you check this, ensure that the receiver is switched off.
Was the recording unsuccessful?
— Faulty operation of the signal source to be recorded.
Remote control is not working.
—
Check
that
the
batteries
of
the
remote
control
are
not
exhausted.
If they are, replace them with two new batteries.
CARE AND MAINTENANCE
The
section
describes
the
care
and
maintenance
tasks
that
must
be
performed
to
optimize
the
operation
of
your
Marantz
equipment.
CLEANING OF EQUIPMENT EXTERNAL SURFACES
The
exterior
finish
of
your
unit
will
last
indefinitely
with
proper
care
and
cleaning.
Never
use
scouring
pads,
steel
wool,
scouring
powders
or
harsh
chemical
agents
(e.g.,
lye
solution),
alcohol,
thinners, benzine, insecticide or other volatile substances as these
will mar the finish of the equipment. Likewise, never use cloths
containing chemical substances. If the equipment gets dirty, wipe the
external surfaces with a soft, lint-free cloth.
If the equipment becomes heavily soiled:
—
dilute
some
washing
up
liquid
in
water,
in
a
ratio
of
one
part
detergent
to
six parts
water.
—
dip
a
soft,
lint
free
in
the
solution
and
wring
the
cloth
out
until
it
is
damp.
— wipe the equipment with the damp cloth.
— dry the equipment by wiping it with a dry cloth.
FUSE REPLACEMENT
If
a
fuse
blows,
unplug
the
equipment
from
the
mains
supply.
Replace
the
fuse
only
with
a
fuse
of
the
same
type
and
rating.
Replacing
the
fuse
with
one
of
a
higher
rating
or
a
slower
action
will
not
protect
the
equipment
and
will
invalidate
the
warranty.
If
the
replacement
fuse
blows
again
after
the
equipment
is
turned
on,
the
equipment
should
be
taken
to
an
authorized
service
facility.
REPAIRS
Only the most competent and qualified service technicians should be
allowed to service the equipment. The Marantz company and its
factory-trained warranty station personnel have the knowledge and
special facilities needed for repair and calibration of this precision
equipment. After the warranty period has expired, repairs will be
performed for a charge if the equipment can be returned to normal
operation.
In the event of difficulty, refer to your dealer or write directly to the
nearest location to you that is listed on the Marantz Authorised
Service Station list. If writing, please include the model and serial
number of the equipment together with a full description of what you
think is abnormal about the equipment's behaviour.