Why is my Marantz SR4300 Receiver remote control not working?
If your Marantz Receiver's remote control isn't working, the batteries might be dead, so replace them with new ones. Ensure that the function-key setting on the remote is correct. Try moving closer to the receiver or changing your position. Also, make sure there are no obstructions between the remote and the receiver.
Why is there no sound coming from the center speaker on my Marantz Receiver?
If you're not getting any sound from the center speaker of your Marantz Receiver, ensure the center speaker cable is correctly connected. If 'STEREO' is selected as the surround mode, no sound will come from the center speaker, so select a different surround mode. Also, check that 'Center = NONE' hasn't been selected in the setup mode and adjust accordingly.
Why is there no sound coming from the surround speakers on my Marantz SR4300 Receiver?
If you're not getting any sound from the surround speakers on your Marantz Receiver, check that the surround speaker cables are correctly connected. If 'STEREO' is selected as the surround mode, no sound will be output from the surround speakers, so select a different surround mode. Also, ensure that 'Surround = NONE' hasn't been selected in the setup mode and adjust accordingly.
Why is there no sound coming from the surround back speakers on my Marantz Receiver?
If you're not getting any sound from the surround back speakers on your Marantz Receiver, ensure the surround back speaker cable is correctly connected. The surround mode must be set to EX/ES. Also, verify that 'Surround back = NONE' hasn't been selected in the SPEAKERS SIZE SETUP and adjust accordingly.
Why is there no output to Sub Woofer Out on my Marantz SR4300 Receiver?
If there's no output to the Sub Woofer Out on your Marantz Receiver, check if 'Sub-woofer = NONE' has been selected in the SETUP mode. If so, select 'Sub-woofer = YES'.
What to do if my Marantz Receiver has no sound and picture even when power is on?
If your Marantz Receiver isn't producing any sound or picture even when powered on, several factors could be at play. First, check if the mute function is activated and deactivate it using the remote. Ensure that all input cables are correctly connected according to the connection diagram. Verify that the master volume isn't turned down completely and that the function selector is set to the correct position.
How to fix FM or AM reception failure on my Marantz SR4300 Receiver?
If you're not getting any FM or AM reception on your Marantz Receiver, the antenna connection might be incomplete. Ensure the indoor FM and AM antennas are correctly connected to their respective outlets on the receiver.
Why is there noise during AM reception on my Marantz SR4300?
If you're experiencing noise during AM reception on your Marantz Receiver, it might be due to interference from other electrical fields. Try changing the location where the AM indoor antenna is set up.
Why is my Marantz Receiver outputting sound from the wrong source?
If your Marantz Receiver is outputting sound and pictures from equipment other than what's selected with the function selector, the input cable might be connected incorrectly. Refer to the connection diagram to ensure the cable is properly connected.
Why is there noise during FM reception on my Marantz Receiver?
If you're hearing noise during FM reception on your Marantz Receiver, the radio waves from the broadcasting station might be weak. Try installing an FM outdoor antenna.
General| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
|---|---|
| Signal to Noise Ratio | 98 dB |
| HDMI Inputs | 0 |
| Component Video Inputs | 2 |
| Digital Audio Inputs | 2 Optical, 1 Coaxial |
| Type | AV Receiver |
| Surround Sound Formats | Dolby Digital, DTS, Dolby Pro Logic II |
| Total Harmonic Distortion | 0.08% |
| Tuner Section | AM/FM |
| Analog Outputs | 2 |
| Input Sensitivity | 200mV |
| Video Inputs | 2 S-Video |
| Video Outputs | 1 S-Video |
To Next Page
