Why is "UPGRADE TUNER" displayed on my Marantz SR6003 Receiver?
If "UPGRADE TUNER" is displayed, the connected XM CNP-1000 is incompatible. Upgrade the XM CNP-1000 to the XM Mini-Tuner and report the model of the AV receiver and the ID number of the CNP-1000 to XM Listener Care.
Why is there no sound and picture output on my Marantz SR6003 Receiver even when it's powered on?
If there's no sound or picture even when the power is on, check these possible causes: * Ensure mute is off using the remote controller. * Verify the input cable is correctly connected according to the connection diagram. * Adjust the master volume if it's turned all the way down. * Select the correct function selector position.
Why is there no audio output from the center channel speaker on my Marantz SR6003 Receiver?
If there is no audio from the center channel, it could be due to a few reasons: * Ensure the center speaker cable is correctly connected. * If STEREO is selected for Surround mode, no sound will be output from the center speaker. Set another Surround mode. * Check that Center is not set to None in SETUP mode. If it is, make the correct setting.
Why is there no audio output from the surround speakers on my Marantz Receiver?
If you're not getting any sound from the surround speakers, here are a few things to check: * Make sure the surround speaker cables are properly connected. * If the Surround mode is set to STEREO, no sound will come from the surround speakers. Choose a different Surround mode. * Verify that Surround is not set to None in the SETUP mode; adjust the setting if needed.
Why is there no audio output from the surround back speakers on my Marantz SR6003 Receiver?
If there's no audio from the surround back speakers, check these things: * Ensure the surround back speaker cable is correctly connected. * The surround mode should be set to EX/ES. * In the SPEAKERS SIZE SETUP, make sure Surround back is not set to None. Adjust the setting as needed.
Why is DVD-Audio not played back over an HDMI connection on my Marantz Receiver?
If DVD-Audio isn't playing over HDMI, the DVD player may not support CPPM, preventing HDMI audio output. Use a DVD-Audio player that supports CPPM, turn on PCM downsampling on the DVD player, or use an analog connection.
Why does "NO AUDIO FILE" appear on the display of my Marantz Receiver when a USB storage device is connected?
If "NO AUDIO FILE" appears, it means there are no playable files recorded on the USB storage device. Record the supported file on a USB storage device.
Why does "CAN'T PLAY" appear on the display of my Marantz Receiver when a USB storage device is connected?
If "CAN'T PLAY" appears, it could be due to: * Attempting to play a copyright-protected file, which the unit cannot play. * The file may be damaged, or its extension and file structure are incompatible. Check the file.
Why can't I select Neo:6 mode on my Marantz Receiver?
If you cannot select Neo:6 mode, it is because the input signal is incompatible. Use a 2 channel DTS input signal, PCM input signal or analog input signal.
Why can't I select EX/ES mode on my Marantz SR6003?
If you cannot select EX/ES mode, it could be due to: * Surround center= None has been selected in SPEAKERS SIZE SETUP. Make the correct setting. * The input signal being incompatible. Use a 5.1channel source.
General warnings about electric shock, fire, and operating hazards.
Compliance statement with FCC rules for digital devices.
Introduction to the SR6003, manual advice, and package contents.
Highlights of audio decoding, GUI, and advanced capabilities.
Identification of front and rear panel controls, displays, and connectors.
Guidelines for speaker placement and connecting audio/video components.
Connecting HDMI devices, antennas, and the AC power cable.
Turning on the unit, selecting inputs, adjusting volume, and basic tuner functions.
Manual tuning, modes, and preset memory operations for the tuner.
Connecting USB storage devices and multi-channel audio sources.
Connecting external amplifiers, bi-amping, and configuring surround parameters.
Programming, editing, and learning functions for the remote control.
Navigating the setup menu using the Graphical User Interface.
Configuring input, speaker, surround, and video settings.
Adjusting preference, EQ, and other system settings.
Selecting and listening to XM and Sirius satellite radio.
Searching channels and managing presets for satellite radio.
Troubleshooting guide for common unit and connection problems.
Resolving specific issues with HDMI, USB, and satellite radio.
Detailed specifications of the unit's performance and capabilities.
Cleaning, repair information, and remote control setup codes.
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 105 dB |
| THD | 0.08% |
| Input Impedance | 47 kOhm |
| Input Sensitivity | 200 mV |
| Tuner Bands | AM/FM |
| HDMI Switching | Yes |
| Frequency Response | 10 Hz - 100 kHz |
| HDMI Pass-Through | Yes |
| AM/FM Tuner | Yes |
| Multi-room Output | Yes |
| Zone 2 Output | Yes |
| Dolby Technologies | Dolby Digital Plus, Dolby TrueHD |
| DTS Technologies | DTS-HD Master Audio |
| Video Upscaling | Up to 1080p |
| Network Connectivity | No |
| Audio D/A Converter | 192kHz/24-bit |
| Output Impedance / Channel | 8 ohms |
| Video Inputs | 4 HDMI, 3 Component, 4 Composite |
| Video Outputs | 1 HDMI, 1 Component, 1 Composite |
| Audio Inputs | Digital coaxial x 2, Digital optical x 2 |
| Audio Outputs | Pre-out |
| Amplifier Output Details | 110W x 7 (8 ohms, 20Hz-20kHz, 0.08% THD) |
| Output Power / Channel | 110W (8 ohms, 20Hz-20kHz, 0.08% THD) |
To Next Page
