Why does it take time for the display of an HDMI connection to appear on my Marantz SR6001?
If it takes time for the display of an HDMI connection to appear on your Marantz Receiver, it is likely due to authentication between the HDMI devices. This is normal for some HDMI devices.
What to do if there is no speaker output from my Marantz Receiver?
If there's no speaker output from your Marantz Receiver, make sure headphones are disconnected from the headphone jack, as speakers will not output sound when headphones are connected.
How to enable subwoofer output on my Marantz SR6001?
If there's no output to the subwoofer from your Marantz Receiver, check if 'Subwoofer = NONE' has been selected in SETUP mode. If so, select 'Subwoofer = YES'.
What to do if my Marantz SR6001 Receiver has power but no sound or picture?
If your Marantz Receiver has power but no sound or picture, check the following: * Make sure the mute function is off. * Verify that the input cables are correctly connected according to the connection diagram. * Increase the master volume. * Ensure the function selector is set to the correct input.
How to fix FM or AM reception failure on my Marantz SR6001 Receiver?
If FM or AM reception fails on your Marantz Receiver, ensure the indoor FM and AM antennas are correctly connected to their respective outlets.
Why is my Marantz Receiver only receiving XM channels 0 and 1?
If your Marantz Receiver is only receiving XM channels 0 and 1, contact XM Radio to activate the XM Tuner.
Why does my Marantz SR6001 display “ANTENNA”?
If “ANTENNA” is displayed on your Marantz Receiver, check that the XM terminal and the XM Mini-Tuner and Home Dock are properly connected.
Why does my Marantz SR6001 Receiver display “NO SIGNAL”?
If “NO SIGNAL” is displayed on your Marantz Receiver, reposition your XM Mini-Tuner and Home Dock.
How to reduce noise during AM reception on my Marantz SR6001?
If you hear noise during AM reception on your Marantz Receiver, try changing the location where the AM indoor antenna is set up, as the reception might be affected by other electrical fields.
How to fix incorrect audio from a channel on my Marantz SR6001?
If you're getting incorrect audio from a channel on your Marantz Receiver, make sure the speaker cable is connected correctly by referring to the connection diagram.
Specifies locations to avoid for optimal performance and safety.
Explains DTS technology for 5.1 channels of discrete digital audio.
Explains NEO:6 for matrix decoding and expanding stereo to multichannel.
Explains DTS-ES Extended Surround for 360-degree surround impression.
Explains DTS 96/24 for high-resolution audio on DVD-Video.
Explains Dolby Pro Logic IIx for immersive 7.1-channel listening.
Explains Dolby Virtual Speaker for virtual surround from two speakers.
Explains Dolby Headphone for surround sound over headphones.
Explains Circle Surround II for multichannel surround sound playback.
Explains HDCD for high-definition compatible digital audio.
Explains HDMI as an interface for digital audio and video transmission.
Explains Audyssey MultEQ for automatic room correction and speaker setup.
Highlights HDMI capabilities for digital audio/video and HDCP support.
Lists supported Dolby, DTS, and Circle Surround technologies.
Details amplifier specs, D/A converters, and power supply design for clarity.
Details multi-room, RS-232C, trigger outputs, and assignable inputs.
Explains the power switch and standby indicator for unit control.
Explains the input selector knob for choosing audio/video sources.
Describes the headphone jack for private listening and automatic speaker muting.
Buttons to select surround modes and auto surround detection.
Buttons to activate Multiroom system and speaker functions.
Explains the volume control knob for adjusting overall sound level.
Controls for accessing, navigating, and confirming setup menu options.
Explains the MultEQ button and MIC jack for automatic speaker measurement.
Explains various indicators like DISP, SLEEP, MULTI, TUNER, DTS-ES, etc.
Shows status, input source, surround mode, volume, and other messages.
Indicates signal formats like PCM, Dolby Digital, DTS, and HDMI.
Terminals for connecting FM and AM antennas.
Jacks for component video, digital audio, and analog audio connections.
Terminals for speaker connections, multi-room audio output, and remote control.
AC outlets, DC trigger output, and remote control interface jacks.
Details the functions and operations of the remote control unit buttons.
Instructions for loading AAA type batteries into the remote control.
Important safety precautions regarding battery usage and disposal.
Details remote control functions when set to AMP mode for the SR6001.
Details remote control functions when set to TUNER mode for the SR6001.
Instructions for controlling Marantz DVD, CD, and VCR players with the remote.
Instructions for controlling Marantz CD recorders, MD decks, and tape decks.
Describes how to use the remote control with Marantz AV equipment.
Explains using the remote with non-Marantz devices and programming codes.
Procedures to check and reset remote control codes.
Step-by-step guide to teach the remote new codes.
Procedures to erase programmed codes by buttons, sources, or all memory.
Guidance on ideal speaker positioning and wiring instructions.
How to connect subwoofers and digital audio components.
Explains HDCP and provides instructions for connecting HDMI devices.
Details the different types of video jacks and their signals.
Connecting 7.1 channel sources and external power amplifiers.
Connecting remote control terminals for synchronized operation.
Ports for external control devices and system integration.
Explains the OSD menu system for operations using remote or front panel.
Details buttons on remote and front panel for navigating the OSD menu system.
For assigning digital inputs to desired source components.
For adjusting speaker levels for 7.1 channel input sources.
For renaming input sources with alphanumeric characters.
Automatically measures and optimizes speaker settings using the microphone.
Allows manual configuration of speaker settings and parameters.
Indicates an issue with the microphone connection or setup.
Indicates excessive noise in the listening room during measurement.
Indicates issues with speaker detection, polarity, or connections.
Configures speaker size, subwoofer presence, and distance for delay calculation.
Adjusts individual speaker output levels for balanced sound.
Sets individual channel volume levels for surround playback.
Fine-tunes surround parameters for music, movies, and games.
Activates Home Theater EQ and sets Low Frequency Effects level.
Converts analog video signals for monitor output and progressive playback.
Enables TV auto power control and on-screen display information.
Configures source selectors, sleep timers, and volume for multi-room audio.
Sets up DC trigger output for controlling external devices.
Sets standby mode, bilingual audio, and HDMI audio handling.
Selects EQ modes like Audyssey, Front, Flat, Preset, or Off.
Manually adjust graphic EQ or check auto EQ results.
How to select input sources and surround sound modes.
How to adjust listening volume and tone (bass, treble) levels.
Features for late-night listening and dialogue clarity.
Converts analog video signals for monitor output and HDMI.
Converts video signals and provides sound muting and sleep timer functions.
Modes for purist audio, bypassing processing, and automatic mode selection.
Various Dolby and DTS surround sound processing options.
Modes for multichannel playback, virtual surround, and stereo.
Important notes and cautions regarding surround mode compatibility and playback.
Controls receiver power based on TV's video input signal.
How to use headphones and activate Dolby Headphone mode.
Turns off unnecessary video circuits to save power.
Temporarily selects audio input modes and explains analog source recording.
Selects between speaker systems A, B, or both.
Describes AUX2 input and Lip Sync adjustment for audio-video synchronization.
How to listen to radio, perform auto/manual tuning, and direct frequency call.
Selects auto stereo or mono mode for FM reception.
How to store and automatically scan for radio stations.
How to select stored stations and display the preset list.
Rearranges stored preset stations to fill gaps in sequence.
Allows alphanumeric naming of preset stations.
Selects XM input source and checks signal strength and Radio ID.
Displays XM information like artist/song title, and category on the front panel.
Methods for finding and storing XM channels via search or presets.
How to play audio from main room sources in another room using out or speaker terminals.
Operates multi-room functions remotely using an IR receiver.
Important notes on system compatibility, limitations, and speaker setup.
Troubleshooting for power-on issues, no sound, or no picture output.
Troubleshooting for no speaker output or incorrect input signals.
Troubleshooting for noise during playback or issues with specific channels.
Troubleshooting for remote control operation, range, and setup errors.
Troubleshooting for XM antenna and signal reception issues.
Solutions for display not appearing or audio not playing over HDMI.
Troubleshooting DVD-Audio over HDMI and HDMI connection timing issues.
Explains memory backup and provides instructions to reset the unit.
Technical details for FM/AM tuners and audio sections.
Technical details for video, HDMI, power, and weight.
List of setup codes for various TV, VCR, and DSS brands.
List of setup codes for various DVD player brands.
General| Audio Channels | 7.1 |
|---|---|
| THD | 0.08% |
| Input Sensitivity | 200 mV |
| Signal to Noise Ratio | 100 dB |
| HDMI Inputs | 3 |
| HDMI Outputs | 1 |
| Component Video Inputs | 3 |
| Component Video Outputs | 1 |
| Digital Audio Inputs (Optical) | 2 |
| Digital Audio Inputs (Coaxial) | 2 |
| Frequency Response | 10 Hz - 100 kHz |
| Surround Sound Formats | Dolby Digital, DTS, Dolby Digital EX, DTS-ES, Dolby Pro Logic IIx |
| Video Conversion | Yes |
| Output Power | 110W (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
To Next Page
