Why Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® cannot be selected on Marantz Receiver?
If Audyssey MultEQ® XT, Audyssey Dynamic EQ®, and Audyssey Dynamic Volume® cannot be selected on your Marantz Receiver: * Switch the surround mode to something other than “DIRECT” or “PURE DIRECT”. * These features cannot be selected when headphones are in use.
How to fix Marantz SR6006 Receiver when it cannot be operated with the remote control?
If your Marantz Receiver isn't responding to the remote control, try these steps: * Replace the batteries with new ones. * Ensure you're within 23 ft/7 m of the unit and within a 30° angle. * Remove any obstacles blocking the remote sensor. * Verify the batteries are inserted correctly, matching the polarity marks. * Shield the unit from strong light sources (like direct sunlight or fluorescent lights). * Confirm the operation mode matches the device you're trying to control.
Why Marantz SR6006 Receiver power does not turn on?
If your Marantz Receiver isn't powering on: * Make sure the power plug is fully inserted into the outlet. * The protection circuit might be active. Unplug the receiver, wait 5-10 seconds, and then plug it back in.
Why no sound is produced from subwoofer on Marantz Receiver?
If your Marantz Receiver's subwoofer isn't producing sound: * Check the subwoofer connections. * Ensure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * If “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, the subwoofer might not output sound depending on the input signal or surround mode.
Why is there no sound from surround speakers on Marantz SR6006 Receiver?
If there's no sound from the surround speakers on your Marantz Receiver, check if the surround speakers are connected to the correct SURROUND terminals.
Why can't I select Dolby PLg mode or DTS NEO:6 mode on Marantz SR6006?
If you can't select Dolby PLg or DTS NEO:6 mode on your Marantz Receiver: * Make sure that “Speaker Config.” – “Center” or “Surround” is not set to “None”. This mode cannot be selected with a 2.0/2.1ch speaker system. * Dolby PLg or DTS NEO:6 cannot be selected when headphones are in use.
How to improve reception on Marantz Receiver?
If your Marantz Receiver is experiencing poor reception with noise or distortion: * Try adjusting the antenna's position or orientation. * Separate the AM loop antenna from the unit. * Consider using an FM outdoor antenna. * Keep the antenna away from other connection cables.
How to turn on display on Marantz SR6006?
If the display on your Marantz Receiver is off, go to the menu and set “Display” to something other than “OFF”.
How do I turn on the display on my Marantz Receiver?
If the display on your Marantz Receiver is off, set “Display” on the menu to something other than “OFF”.
How to troubleshoot a Marantz SR6006 that does not turn on?
If your Marantz Receiver isn't powering on: * Check that the power plug is correctly inserted into the power outlet. * The protection circuit might be active. Disconnect the power plug, wait 5-10 seconds, and then reconnect it.
General| Receiver type | Surround |
|---|---|
| Pre-out channels | 7.2 |
| Speaker selector | A+B |
| Pre-out connectivity | Yes |
| Audio output channels | 7.1 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 110 W |
| HDMI in | 7 |
| Composite video in | 5 |
| Ethernet LAN (RJ-45) ports | 1 |
| Component video (YPbPr/YCbCr) in | 2 |
| Multichannel audio output type | Terminals |
| Connectivity technology | Wired |
| Speakers connectivity type | - |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Image formats supported | JPG |
| Wi-Fi | No |
| Supported radio bands | FM |
| Internet radio services supported | Last.fm, vTuner |
| Product color | Black |
| Audio decoders | Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS-ES, DTS-HD Master Audio |
| Volume control | Rotary |
| Apple docking compatibility | iPod |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.2 W |
| Power consumption (typical) | 650 W |
| Supported video modes | 1080p |
| Supported graphics resolutions | 1920 x 1080 (HD 1080) |
Weight and Dimensions| Depth | 389 mm |
|---|---|
| Width | 440 mm |
| Height | 161 mm |
| Weight | 11400 g |
To Next Page
