Why can't I select Audyssey DSX on my Marantz Receiver?
If you're unable to select Audyssey DSX™ on your Marantz Receiver: * Ensure that “Speaker Config.” – “Front Height” or “Front Wide” is set to something other than “None”. * Also, check that “Speaker Config.” – “Center” is set to something other than “None”. * Switch the surround mode to AUTO. * Audyssey DSX™ cannot be selected when headphones are used.
Why is there no sound from the subwoofer connected to my Marantz SR6006?
If your subwoofer isn't producing sound with your Marantz Receiver: * Verify the subwoofer connections. * Ensure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * Note that if “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, sound output may vary based on the input signal or surround mode.
How to fix Marantz SR6006 Receiver when it cannot be operated with the remote control?
If your Marantz Receiver isn't responding to the remote control, try these steps: * Replace the batteries with new ones. * Ensure you're within 23 ft/7 m of the unit and within a 30° angle. * Remove any obstacles blocking the remote sensor. * Verify the batteries are inserted correctly, matching the polarity marks. * Shield the unit from strong light sources (like direct sunlight or fluorescent lights). * Confirm the operation mode matches the device you're trying to control.
Why Marantz SR6006 Receiver power does not turn on?
If your Marantz Receiver isn't powering on: * Make sure the power plug is fully inserted into the outlet. * The protection circuit might be active. Unplug the receiver, wait 5-10 seconds, and then plug it back in.
Why no sound is produced from subwoofer on Marantz Receiver?
If your Marantz Receiver's subwoofer isn't producing sound: * Check the subwoofer connections. * Ensure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * If “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, the subwoofer might not output sound depending on the input signal or surround mode.
Why is there no sound from surround speakers on Marantz SR6006 Receiver?
If there's no sound from the surround speakers on your Marantz Receiver, check if the surround speakers are connected to the correct SURROUND terminals.
What does it mean when the power indicator is blinking red in intervals of approximately 2 seconds on Marantz SR6006 Receiver?
If the power indicator on your Marantz Receiver is blinking red every 2 seconds: * The unit may be overheating. Turn off the power and allow it to cool down before turning it back on. * Ensure the unit is installed in a well-ventilated area.
Why is there no sound from surround back speaker on Marantz Receiver?
If there's no sound from the surround back speakers on your Marantz Receiver: * Verify that “Amp Assign” is correctly configured to output audio to the surround back speakers. * Ensure “Speaker Config.” – “Surr.Back” is not set to “None” in the menu. * The surround mode must be set to something other than “STEREO” or “VIRTUAL“.
Why is there no sound from front height speaker on Marantz SR6006?
If there's no sound from the front height speakers on your Marantz Receiver: * Check if “Amp Assign” is correctly configured to output audio from the front height speakers. * Ensure “Speaker Config.” – “Front Height” is set to something other than “None” in the menu.
What does it mean when the power indicator is blinking red in intervals of approximately 0.5 seconds after turning on the Marantz SR6006?
If, after turning on your Marantz Receiver, the power indicator blinks red every 0.5 seconds, the unit's amplifier circuit has likely failed. Turn off the power and contact a Marantz service advisor.
General| Receiver type | Surround |
|---|---|
| Pre-out channels | 7.2 |
| Speaker selector | A+B |
| Pre-out connectivity | Yes |
| Audio output channels | 7.1 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 110 W |
| HDMI in | 7 |
| Composite video in | 5 |
| Ethernet LAN (RJ-45) ports | 1 |
| Component video (YPbPr/YCbCr) in | 2 |
| Multichannel audio output type | Terminals |
| Connectivity technology | Wired |
| Speakers connectivity type | - |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Image formats supported | JPG |
| Wi-Fi | No |
| Supported radio bands | FM |
| Internet radio services supported | Last.fm, vTuner |
| Product color | Black |
| Audio decoders | Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS-ES, DTS-HD Master Audio |
| Volume control | Rotary |
| Apple docking compatibility | iPod |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.2 W |
| Power consumption (typical) | 650 W |
| Supported video modes | 1080p |
| Supported graphics resolutions | 1920 x 1080 (HD 1080) |
Weight and Dimensions| Depth | 389 mm |
|---|---|
| Width | 440 mm |
| Height | 161 mm |
| Weight | 11400 g |
To Next Page
