To Next Page
B
Brandon GeorgeSep 23, 2025
How to enable DTS sound output on Marantz Stereo Receiver?
- SsweeneykimberlySep 23, 2025
If DTS sound is not being output by your Marantz Stereo Receiver, set “Decode Mode” on the menu to “Auto” or “DTS.”
How to enable DTS sound output on Marantz Stereo Receiver?
If DTS sound is not being output by your Marantz Stereo Receiver, set “Decode Mode” on the menu to “Auto” or “DTS.”
Why is there no audio output from my Marantz Stereo Receiver?
If there's no audio output from your Marantz Stereo Receiver, consider the following: 1. Check all device connections and speaker connections to ensure they are secure. 2. Verify that the audio device is powered on. 3. Adjust the master volume and ensure mute mode is off. 4. Select a suitable input source and input mode. 5. If headphones are connected, disconnect them.
Why is there no sound from the surround back speaker on my Marantz Stereo Receiver?
If there is no sound from the surround back speaker of your Marantz Stereo Receiver, set “Amp Assign” on the menu to “Normal.” Also, set “Speaker Config.” – “S.Back” on the menu to something other than “None.” Finally, ensure the surround mode is not set to “STEREO.”
Why is there no sound from the front height speaker on my Marantz Stereo Receiver?
If there is no sound from the front height speaker on your Marantz Stereo Receiver, set “Amp Assign” on the menu to “Normal.” Also, set “Speaker Config.” – “F.Height” on the menu to something other than “None.”
Why is there no sound from the subwoofer connected to my Marantz Stereo Receiver?
If no sound is produced from the subwoofer connected to your Marantz Stereo Receiver: 1. Check the subwoofer connections. 2. Turn on the subwoofer’s power. 3. Set “Speaker Config.” – “Subwoofer” on the menu to “Yes.” 4. If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
How to get sound from subwoofer on Marantz Receiver?
If you're not getting sound from the subwoofer: * Check the subwoofer connections. * Make sure the subwoofer is powered on. * Set “Speaker Config.” – “Subwoofer” to “Yes” in the menu. Note: If “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or surround mode.
How to get sound from surround back speaker on Marantz Receiver?
To get sound from the surround back speaker: * Set “Amp Assign” to “Normal” in the menu. * Set “Speaker Config.” – “S.Back” to something other than “None”. * Ensure the surround mode is not set to “STEREO”.
Why is there no picture appearing on my Marantz SR6005?
If no picture appears: * Check the TV connection. * Set the TV input correctly.
What to do if Marantz Receiver power indicator is blinking red after turning on?
If the power indicator blinks red at 0.5-second intervals after powering on, the unit's amplifier circuit may have failed. Turn off the power and contact a Marantz service advisor.
How to troubleshoot a Marantz SR6005 that is not operating properly?
If your Marantz Receiver isn't working as expected, try resetting the microprocessor.
Essential safety warnings and operating instructions to prevent hazards.
Recommendations for proper unit placement and ventilation.
Details on discrete channels, HDMI support, and audio technologies.
Step-by-step guide for initial setup and basic operation.
Automatic speaker calibration for optimal sound.
Instructions for connecting various audio and video sources.
Selecting sources, adjusting volume, and basic playback.
Manual settings for speaker size, presence, and bass reproduction.
Programming the remote to control other devices.
Solutions for common operational and audio issues.
Detailed performance data for audio, video, tuner, and general sections.
Steps to reset the unit to factory default settings.
General| Channels | 7.1 |
|---|---|
| Power Output | 110W per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
| HDMI Inputs | 6 |
| HDMI Outputs | 1 |
| Dolby Technologies | Dolby TrueHD, Dolby Digital Plus, Dolby Pro Logic IIz |
| Networking | No |
| 3D Support | Yes |
| Audio Return Channel (ARC) | Yes |
| Phono Input | Yes |
| Total Harmonic Distortion | 0.08% |
| Signal-to-Noise Ratio | 100 dB |
| Input Sensitivity | 200 mV |
| USB Port | Yes |
| DTS Technologies | DTS-HD Master Audio, DTS Neo:6 |
| Multi-room | Yes |
| Frequency Response | 10Hz-100kHz |
| Video Upconversion | Yes |
