How to get sound from front wide speaker on Marantz SR6007?
To get sound from the front wide speakers, check if 'Assign Mode' is set correctly. Also, ensure 'Speaker Config.' – 'Front Wide' on the menu is set to something other than 'None'.
Why is the STANDBY indicator blinking red on my Marantz SR6007 Receiver?
If the STANDBY indicator is blinking red every 2 seconds, it means the protection circuit is active due to a temperature rise inside the unit. Turn off the power and allow the unit to cool down before turning it back on. Also, reinstall the unit in a location with better ventilation.
What to do if my Marantz SR6007 Receiver power automatically switches to standby mode?
Your Marantz Receiver might be switching to standby mode automatically because the sleep timer is set. Turn the power on again, or change the sleep timer settings. Alternatively, 'Auto Standby' may be enabled; it activates when there's no operation for a while. To disable it, set 'Auto Standby' on the menu to 'Off'.
How to get sound from subwoofer on Marantz Receiver?
If you're not getting sound from the subwoofer, start by checking the subwoofer connections and ensuring the subwoofer is powered on. Then, on the receiver, set 'Speaker Config.' – 'Subwoofer' on the menu to 'Yes'. Note that if 'Front' and 'Center' for 'Speaker Config.' are set to 'Large', and 'Subwoofer Mode' is set to 'LFE', no sound may be output from the subwoofers, depending on the input signal or selected sound mode.
Why is there no audio output with HDMI connection on my Marantz Receiver?
If you're not getting audio through HDMI, first, check the HDMI connector's connection. Then, depending on where you want the audio, check your 'HDMI Audio Out' settings. To output HDMI audio from the speakers, set 'HDMI Audio Out' on the menu to 'AVR'. If you want the audio from your TV, set it to 'TV'.
What to do if no video is output with HDMI connection on Marantz SR6007 Receiver?
If you're not getting a video signal via HDMI, make sure the input source matches the HDMI connector you're using. Also, verify that your TV is compatible with HDCP (High-bandwidth Digital Content Protection). If the connected device isn't HDCP-compliant, the video may not display correctly.
Why is The AirPlay icon not displayed in iTunes?
If the AirPlay icon isn't showing up, make sure your Marantz Receiver and the computer or iPhone/iPod touch/iPad are connected to the same network (LAN). Also, ensure that iTunes or the iPhone/iPod touch/iPad have the latest firmware that supports AirPlay installed.
How do I play DTS sound on my Marantz SR6007?
Set 'Decode Mode' on the menu to 'Auto' or 'DTS'.
How to get sound from front height speaker on Marantz SR6007?
To get sound from the front height speakers, check if 'Assign Mode' is set appropriately. Also, make sure 'Speaker Config.' – 'Front Height' on the menu is set to something other than 'None'.
How do I fix the volume not increasing on my Marantz Receiver?
If the volume isn't increasing, the maximum volume might be set too low. Adjust the maximum volume using 'Limit' in the menu. Also, check if the power for external devices connected to the unit's output connectors is turned on.
Crucial safety guidelines for operating the AV receiver.
Guides on using Audyssey® Setup for automatic speaker optimization.
Instructions on optimal placement of the setup microphone.
Outlines the initial steps for speaker detection and measurement.
Details the process for taking measurements at multiple listening positions.
Explains the analysis performed after measurements are complete.
Guides on reviewing, saving, and completing the Audyssey® Setup.
Explains network playback requirements and supported file types.
Guides on streaming music from Apple devices using AirPlay.
Covers advanced procedures for speaker setup and configuration.
Details on connecting different speaker configurations (7.1ch, 5.1ch, etc.).
Explains the HDMI control function for device interoperability.
Details the procedure for enabling and using HDMI control features.
Details on configuring HDMI output for video and audio signals.
Details on assigning HDMI inputs to sources and menu operations.
Overview of Audyssey® Setup and manual speaker configuration options.
Guides on assigning amplifiers based on speaker system configuration.
Explains how to indicate speaker presence and select size categories.
General| Receiver type | Surround |
|---|---|
| Pre-out channels | 7.2 |
| Pre-out connectivity | Yes |
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/192kHz |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 110 W |
| HDMI in | 6 |
| Composite video in | 4 |
| Ethernet LAN (RJ-45) ports | 1 |
| Component video (YPbPr/YCbCr) in | 2 |
| Connectivity technology | Wired |
| Speakers connectivity type | RCA |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Image formats supported | JPG |
| Wi-Fi | No |
| Supported radio bands | - |
| Product color | Black |
| Audio decoders | Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS-ES, DTS-HD Master Audio |
| Apple docking compatibility | iPhone, iPod |
| Number of products included | 1 pc(s) |
| Power consumption (standby) | 0.2 W |
| Power consumption (typical) | 650 W |
Weight and Dimensions| Depth | 389 mm |
|---|---|
| Width | 440 mm |
| Height | 161 mm |
| Weight | 11400 g |
To Next Page
