Why is there no sound from surround back speaker on my Marantz SR5006?
If you're not hearing sound from the surround back speakers on your Marantz Receiver, consider the following: * Confirm that “Amp Assign” is correctly configured to output audio to the surround back speakers. * In the menu, ensure “Speaker Config.” – “S.Back” is set to something other than “None”. * Make sure the surround mode is not set to “STEREO” or “VIRTUAL”.
Why is there no sound from front height speaker on my Marantz Receiver?
If there's no sound coming from the front height speaker of your Marantz Receiver, check these settings: * Verify that “Amp Assign” is properly configured to send audio to the front height speakers. * Ensure that “Speaker Config.” – “F.Height” in the menu is set to something other than “None”.
How to fix no sound from subwoofer on Marantz SR5006 Receiver?
If your Marantz Receiver's subwoofer isn't producing sound, try these troubleshooting steps: * Check all subwoofer connections. * Make sure the subwoofer is powered on. * In the receiver's menu, set “Speaker Config.” – “Subwoofer” to “Yes”. * Note: If “Front” and “Center” are set to “Large” in “Speaker Config.” and “Subwoofer Mode” is set to “LFE”, the subwoofer might not output sound, depending on the input signal or selected surround mode.
What to do if there is no audio output with HDMI connection on my Marantz Receiver?
If you're not getting audio through your HDMI connection on your Marantz Receiver, try these steps: * Check the HDMI connectors to ensure they are properly connected. * If you want audio from the speakers, go to the menu and set “HDMI Audio Out” to “AMP”. * If you prefer audio from your TV, set “HDMI Audio Out” to “TV” in the menu.
What to do if there is no video output with HDMI connection on my Marantz Receiver?
If you're experiencing a 'no video output' issue with your Marantz Receiver's HDMI connection, please check the following: * Ensure the HDMI connectors are securely plugged in. * Verify that the input source on your receiver matches the connected HDMI connector. * Confirm that your TV supports HDCP (High-bandwidth Digital Content Protection). If the connected device isn't HDCP-compatible, the video output may not work correctly.
What to do if my Marantz Receiver power does not turn on?
If your Marantz Receiver isn't powering on, try these solutions: * Make sure the power plug is fully and correctly inserted into the power outlet. * The protection circuit might be active. Unplug the receiver from the outlet, wait 5 to 10 seconds, and then plug it back in.
How to fix no audio output on Marantz SR5006?
If you're not getting any audio from your Marantz Receiver, here's what you can check: * Verify all device connections. * Inspect speaker connections and configurations. * Ensure the audio device is powered on. * Adjust the master volume. * Deactivate mute mode. * Choose the correct input source and mode. * Disconnect any headphones, as they may be preventing sound from the speakers.
Why I can't select Dolby PLg mode or DTS NEO:6 mode on Marantz Receiver?
If you're unable to select Dolby PLg or DTS NEO:6 mode on your Marantz Receiver, it might be due to these reasons: * Ensure that “Speaker Config.” – “Center” or “Surround” is set to something other than “None”. These surround modes cannot be selected if the speaker system is 2.0/2.1ch. * Dolby PLg or DTS NEO:6 cannot be selected when headphones are in use.
Why can't I select Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® on my Marantz SR5006?
If you're having trouble selecting Audyssey MultEQ® XT, Audyssey Dynamic EQ®, and Audyssey Dynamic Volume® on your Marantz Receiver: * Switch the surround mode to something other than “DIRECT” or “PURE DIRECT”. * These features cannot be selected when headphones are in use.
How to fix DTS sound not output on Marantz SR5006?
If you're not getting DTS sound from your Marantz Receiver, set “Decode Mode” in the menu to either “Auto” or “DTS”.
General| Audio output channels | 7.1 channels |
|---|---|
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Power output per channel (20-20KHz@8 Ohm) | 100 W |
| Ethernet LAN (RJ-45) ports | 1 |
| Connectivity technology | Wired |
| Speakers connectivity type | RCA |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Wi-Fi | No |
| Ethernet LAN | Yes |
| AM band range | 520 - 1710 kHz |
| FM band range | 87.5 - 107.9 MHz |
| Supported radio bands | AM, FM |
| Preset stations quantity | 56 |
| Display | LED |
| Product color | Black |
| Audio decoders | DTS 96/24, DTS-ES, DTS-HD Master Audio |
| Apple docking compatibility | iPhone, iPod |
| AC input voltage | 120 V |
| AC input frequency | 60 Hz |
| Power consumption (standby) | 0.2 W |
| Power consumption (typical) | 650 W |
Weight and Dimensions| Depth | 389 mm |
|---|---|
| Width | 440 mm |
| Height | 161 mm |
| Weight | 10600 g |
To Next Page
