What to do if a specific channel doesn't produce output on Marantz SR5003?
If a specific channel does not produce output on your Marantz Receiver, check the encoded channel on the source side to ensure there is content recorded there.
Why does the remote controller fail to work with my Marantz Receiver?
If you are unable to control your Marantz Receiver with the remote controller, try replacing all the batteries with new ones. Ensure that the remote controller's function-key setting is correct for the equipment you are trying to control. Make sure you are within a reasonable distance from the unit and that there are no obstructions blocking the path between the remote and the receiver.
How to fix Marantz Receiver display when it doesn't appear over HDMI connection?
If the display does not appear over an HDMI connection with your Marantz Receiver, ensure you are using an HDCP-compatible monitor or projector. Also, verify that the HDMI input on your TV and the HDMI output on the source component are enabled. Check the HDMI mode settings on the receiver, and ensure the HDMI output video resolution of the source component matches your TV's specifications. Use a high-quality HDMI cable (5m or shorter). Make sure the receiver is powered on and try power cycling the unit, TV, and source component. Finally, set the HDMI OUT RES setting to AUTO.
How to enable subwoofer output on Marantz Receiver?
If you are not getting any output to the Subwoofer Out on your Marantz Receiver, it is likely that "Subwoofer = NONE" has been selected in the SETUP mode. To resolve this, go to the SETUP mode and select "Subwoofer = YES".
Why is there no audio from the center channel speaker on my Marantz Receiver?
If you are not getting any audio output from the center channel speaker of your Marantz Receiver, ensure the center speaker cable is correctly connected. Also, if "STEREO" is selected for Surround mode, no sound will be output from the center speaker, so set another Surround mode. Finally, check that "Center = NONE" has not been selected in SETUP mode; if it has, correct the setting.
Why can't I get programmed stations on my Marantz SR5003 Receiver?
If you cannot get programmed station when the PRESET button is pressed on your Marantz Receiver, preset data has likely been erased. This can happen if the power plug is disconnected for long periods. Input the preset data again.
How do I eliminate noise during AM reception on my Marantz SR5003?
If you hear noise during AM reception on your Marantz Receiver, the reception may be affected by other electrical fields. Try changing the location where the AM indoor antenna is set up.
How to reduce FM reception noise on Marantz SR5003?
If you hear noise during FM reception on your Marantz Receiver, the radio waves from the broadcasting station may be weak. Try installing an FM outdoor antenna.
What to do if my Marantz SR5003 cannot be turned on?
If your Marantz Receiver cannot be turned on, ensure that the power plug is securely connected to the outlet.
How to stop noise during DTS CD playback on Marantz Receiver?
If you are hearing noise during DTS-encoded CD or laser disc playback on your Marantz Receiver, and "Analog" has been selected for input, ensure you perform a digital connection. Select digital input, and then play the source.
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 3 |
| HDMI Outputs | 1 |
| Component Video Inputs | 3 |
| Component Video Outputs | 1 |
| Digital Audio Inputs | 2 Optical, 2 Coaxial |
| Analog Audio Inputs | 6 |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 105 dB |
| Total Harmonic Distortion | 0.08% |
| Input Sensitivity | 200 mV |
| Tuner Bands | AM/FM |
| Dolby Decoding | Dolby Digital Plus, Dolby TrueHD |
| DTS Decoding | DTS-HD Master Audio |
| Input Impedance | 47 kOhm |
| Video Conversion | Analog to HDMI |
| Audio Decoders | Dolby TrueHD, DTS-HD Master Audio |
| Power Output | 90 W per channel (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
To Next Page
