Why can't I select EX/ES mode on my Marantz SR5003?
If you cannot select EX/ES mode on your Marantz Receiver, it may be because "Surround center= NONE" has been selected in SPEAKERS SIZE SETUP. Make the correct setting. Alternatively, the input signal may be incompatible, so use a 5.1channel source.
What to do if my Marantz Receiver has no sound and picture even when powered on?
If you are experiencing no sound and picture output even when your Marantz Receiver is powered on, first, ensure that the mute function is off by using the remote controller. Next, check that the input cables are correctly connected according to the connection diagram. Also, verify that the master volume control is not turned all the way down and that the function selector is set to the correct position.
How to fix incorrect audio channel on Marantz SR5003?
If you are experiencing incorrect audio from a channel on your Marantz Receiver, it's possible that the speaker cable is connected incorrectly. Refer to the connection diagram and ensure the cable is properly connected.
How to stop noise during DTS CD playback on Marantz Receiver?
If you are hearing noise during DTS-encoded CD or laser disc playback on your Marantz Receiver, and "Analog" has been selected for input, ensure you perform a digital connection. Select digital input, and then play the source.
Why is there no audio output from the surround back speakers on my Marantz SR5003 Receiver?
If you are not getting any audio output from the surround back speakers on your Marantz Receiver, ensure that the surround back speaker cable is correctly connected. Also, the surround mode must be set to EX/ES. Finally, make sure that "Surround back = NONE" has not been selected in SPEAKERS SIZE SETUP; if it has, correct the setting.
Why is there no audio output from the surround speakers on my Marantz SR5003 Receiver?
If you are not getting any audio output from the surround speakers of your Marantz Receiver, first check that the surround speaker cables are correctly connected. If "STEREO" has been selected for Surround mode, no sound will be output from the surround speakers, so select a different Surround mode. Finally, ensure that "Surround = NONE" has not been selected in SETUP mode; if it has, correct the setting.
How to troubleshoot incorrect audio or video source on Marantz SR5003?
If you are experiencing incorrect audio or video for the selected source on your Marantz Receiver, the input cable might be connected incorrectly. Refer to the connection diagram and ensure the cable is properly connected.
Why is there no speaker output from my Marantz Receiver?
If you are not getting any speaker output from your Marantz Receiver, ensure that headphones are not connected to the headphone jack, as speakers will not output sound when headphones are connected.
Why is there no audio from the center channel speaker on my Marantz Receiver?
If you are not getting any audio output from the center channel speaker of your Marantz Receiver, ensure the center speaker cable is correctly connected. Also, if "STEREO" is selected for Surround mode, no sound will be output from the center speaker, so set another Surround mode. Finally, check that "Center = NONE" has not been selected in SETUP mode; if it has, correct the setting.
How to enable subwoofer output on Marantz Receiver?
If you are not getting any output to the Subwoofer Out on your Marantz Receiver, it is likely that "Subwoofer = NONE" has been selected in the SETUP mode. To resolve this, go to the SETUP mode and select "Subwoofer = YES".
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 3 |
| HDMI Outputs | 1 |
| Component Video Inputs | 3 |
| Component Video Outputs | 1 |
| Digital Audio Inputs | 2 Optical, 2 Coaxial |
| Analog Audio Inputs | 6 |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 105 dB |
| Total Harmonic Distortion | 0.08% |
| Input Sensitivity | 200 mV |
| Tuner Bands | AM/FM |
| Dolby Decoding | Dolby Digital Plus, Dolby TrueHD |
| DTS Decoding | DTS-HD Master Audio |
| Input Impedance | 47 kOhm |
| Video Conversion | Analog to HDMI |
| Audio Decoders | Dolby TrueHD, DTS-HD Master Audio |
| Power Output | 90 W per channel (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
To Next Page
